Fluke 5700A Series II - Page 332

5700A/5720A Series II
Operators Manual
4
—G—
GAL remote command, 5-29
GND Binding Post, 3-10
Guarding, 4-15
—H—
Hazard, Shock, Safety Summary Sheet, 4-4
HI Output Binding Post, 3-10
Hz key, 3-8
—I—
IEEE-488 Connector, 3-13
IEEE-488 Interface, 5-4
Configuration, 5-54
Connector, 5-60
IEEE-488 Interface Cables (Y8021, Y8022, and
Y8023), 8-4
INCR remote command, 5-30
Input Buffer Operation, remote control, 5-10
Inspection, 2-3
Installing
Auxiliary Amplifiers, 2-8
the 5700A/5720A Series II, 2-4
Instruction Manuals. See Manuals, additional
Instrument Setup, 4-7
Instrument Status Change Enable Register, 5-51
Bit Assignments for the ISR, ISCR, and
ISCE, 5-51
Loading the ISCE, 5-52
Reading the ISR, ISCR, and ISCE, 5-52
Instrument Status Change Register, 5-51
Bit Assignments for the ISR, ISCR, and
ISCE, 5-51
Reading the ISR, ISCR, and ISCE, 5-52
Instrument Status Register, 5-51
Bit Assignments for the ISR, ISCR, and
ISCE, 5-51
Reading the ISR, ISCR, and ISCE, 5-52
Interface Cables
Null-Modem Cables, RS-232C (Y1702 and
Y1703), 8-4
Shielded IEEE-488 (Y8021, Y8022, and
Y8023), 8-4
Interface Messages, 5-58
Interface, IEEE-488, 5-4
Interface, RS-232C, 6-3
Internal Clock/Calendar, setting, 4-9
ISCE remote command, 5-30
ISCE? remote command, 5-30
ISCR? remote command, 5-31
ISR? remote command, 5-31
—K—
Keypad, numeric, 3-9
Keys
add/subtract, 3-9
amperes, 3-8
Ampl/Freq, 3-6
arrow, 3-6
Boost, 3-6
Clear Entry (CE), 3-8
dBm, 3-8
divide by 10, 3-7
Enter, 3-8
Ex Grd, 3-5
Ex Sns, 3-4
Hz, 3-8
kilo, 3-9
Limit, 3-7
mega, 3-9
micro, 3-9
milli, 3-9
multiplier, 3-9
multiply by 10, 3-7
New ref, 3-8
numeric keypad, 3-9
Offset, 3-8
ohms, 3-8
Oper/Stby, 3-4
output function, 3-8
Prev Menu, 3-6
Reset, 3-6
Scale, 3-7
Spec, 3-8
volts, 3-8
W Bnd, 3-5
Knob, 3-6, 4-38
—L—
Label, line power and fuse rating, 2-7
Lead drop compensation circuitry, 4-32
Limit key, 3-7
LIMIT remote command, 5-31
LIMIT? remote command, 5-31
Limits, setting, 4-50
Line Power Cords, 2-6
Line Voltage, 2-6
Line voltage and fuse rating label, 2-7
Line voltage selection switches, 2-7
Line Voltage Switch, 3-14
Linearity Checking Using Offset and Scale, 4-47
Linearity Error, 4-44
LO Output Binding Post, 3-10
LOCAL serial remote command, 5-42
LOCKOUT serial remote command, 5-42
Low Thermal EMF Test Leads, 8-4
Low thermal emf test leads (5440A-7002), 4-13