Fluke 5700A Series II - Page 333

Index (continued)
5
—M—
Maintenance
cleaning, 7-6
Manuals, additional, 1-4
Menu Tree, 3-14
Meter response vs. stimulus, 4-48
MULT remote command, 5-32
Multiplier Keys, 3-9
multiply by10 key, 3-7
—N—
N type connector, 3-10
New ref key, 3-8
NEW REF key, 4-63, 4-64
New reference, establishing, 4-39
NEWREF remote command, 5-32
Numeric Keypad, 3-9
—O—
Offset Error, 4-42
Offset key, 3-8
OFFSET key, 4-47
Offset Programming, 4-45
OFFSET remote command, 5-32
OFFSET? remote command, 5-32
OHMREF? remote command, 5-33
Ohms key, 3-8
OLDREF remote command, 5-33
ONTIME? remote command, 5-33
OPER remote command, 5-34
Oper/Stby key, 3-4
Operate and Standby Modes, 4-13
Operating State Transitions, 5-44
OUT remote command, 5-34
OUT? remote command, 5-34
OUT_ERR? remote command, 5-34
OUTPUT Binding Post, 3-10
AUX CURRENT, 3-10
HI, 3-10
LO, 3-10
OUTPUT Binding Posts, 3-12
Output Display, 3-4
Output Function Keys, 3-8
Output Limits, setting, 4-50
Current Limits, setting, 4-50
Voltage Limits, setting, 4-50
Output, setting, 4-22
AC Current, 4-28
AC Voltage, 4-25
Auxiliary Amplifier, 4-37
DC Current, 4-27
DC Voltage, 4-24
Resistance, 4-30
Variable Phase, 4-34
Wideband AC Voltage(Option 5700A-03), 4-32
—P—
Parameters
Remote command, 5-8
Serial Communication, 6-4
Setup, 4-6
Performance History, developing, 1-11
Performing a Wideband Flatness Test, 4-63
Phase Controls menu, 4-34
Phase Lock In BNC Connector, 3-12
Phase locking to an external signal, 4-34
Phase Locking to an External Signal, 4-35
PHASE remote command, 5-35
PHASE? remote command, 5-35
PHASELCK remote command, 5-35
PHASESFT remote command, 5-35
Placement and Rack Mounting, 2-4
Power Switch, 3-6
Powering on the Calibrator, 4-3, 4-4
Prev Menu key, 3-6
Printing Calibration Reports, 6-6
About calibration reports, 1-10
Calibration Check Shift Results, 6-7
Calibration Shift Results, 6-6
Generating a Printout, 6-8
remote program to print a report, 5-61
Programming a Scale Factor, 4-46
Programming an Offset, 4-45
—Q—
Queue, fault, 5-53
—R—
Rack Mount Kits (Y5737 and Y5735), 2-4, 8-4
Range Calibration, 1-11, 7-14
Range Identifiers for Remote Commands, 5-42
RANGE? remote command, 5-36
RANGELCK remote command, 5-36
RCOMP remote command, 5-36
Reading the UUT Error
AC and DC VOltage and Current Output, 4-40
Resistance Output, 4-41
Rear Panel Binding Posts, 3-12
Rear Panel Features, 3-12
Reference Guides, 1-4
REFOUT? remote command, 5-36
Remote Commands, 5-10
Coupled, 5-11
Extra Space Characters, 5-9
Ignored When not in Remote, 5-12
Long Term, 5-12
Multiple, 5-11
Overlapped, 5-12