Fluke 5700A Series II - Page 334

5700A/5720A Series II
Operators Manual
6
Parameter syntax rules, 5-7
Requiring the Calibration Switch to be set, 5-12
Response Message Syntax, 5-10
Sequential, 5-12
Syntax information, 5-7
Terminators, 5-9
Remote Control, IEEE-488 and common
elements of RS-232, 5-4
Address Selection, 5-5
Bus Setup Procedure, 5-4
IEEE-488 Address Selection, 5-5
IEEE-488 Bus Restrictions, 5-4
Incoming Character Processing, 5-9
Input Buffer Operation, 5-10
Interface Messages Accepted, 5-59
Language Selection, 5-5
Port Setup, 5-5
Remote and Local State Transitions, 5-43
Remote State, 5-43
Remote with Lockout State, 5-44
Setup Procedure, 5-4
Terminators, 5-9
Remote Control, RS-232 Specific, 5-5
Exceptions for serial remote control, 5-7
Remote port setup, 5-6
Setup procedure, 5-6
Remote Program Examples, 5-61
*WAI, using, 5-66
Calibration, 5-63
Calibration check, 5-64
DC Zeros, 5-62
OPC, using, 5-66
OPC?, using, 5-66
Printing main output calibration shift
results, 5-61
Remote Calibration, 5-62
Verifying a meter, 5-62
Wideband AC Module (Option 5700A-03) Gain
Calibration, 5-65
REMOTE serial remote command, 5-42
Reset key, 3-6
RESET key, 4-12
Resetting the Calibrator, 4-12
Resistance Output, 4-30
Resistance Value Table, 4-30
Resistance units key, 3-8
Resistors
standard, 742A series, 8-5
Rotary Knob, 3-6
RPT_STR remote command, 5-37
RPT_STR? remote command, 5-37
RS 232C Connector, 3-13
RS-232C Interface
Parameters, 6-4
Printing. See Printing Caliibration Reports
Setup, 6-4
Specifications, 6-3
RS-232C Null-Modem Cables (Y1702 and
Y1703), 8-4
—S—
Sample Applications, 4-51
SCAL_ERR? remote command, 5-38
Scale Error, 4-43
Scale key, 3-7
SCALE key, 4-47
SCALE remote command, 5-37
SCALE? remote command, 5-37
Screen Saver, 3-3
Selecting Amplifiers, 4-10
Selecting Line Voltage, 2-6
Selecting Output Binding Posts, 2-8
SENSE Binding Post, 3-10
SENSE binding posts, 4-15
SENSE Binding Posts, 3-12
Sensing, external, when to use, 4-14
Serial Poll Status Byte, 5-47
Serial Port Remote Control. See Remote Control,
RS-232C
Service Centers, 1-7
Service Information, 2-4
Setting up
IEEE-488 interface, 5-4
Installing the 5700A/5720A Series II, 2-4
RS-232C Serial Interface, 6-4
Setting Up
Menu, 4-6
Parameters, 4-6
Setup Menu, 4-6
Shipping Container, 2-3
Shock Hazard. Safety Summary Sheet, 4-4
Softkey Menu Tree, 3-14, 3-16
Softkeys, 3-6
SP_EOF remote command, 5-38
SP_EOF? remote command, 5-38
SP_SET remote command, 5-38
SP_SET? remote command, 5-39
SP_TIME remote command, 5-39
SP_TIME? remote command, 5-39
Spec Format Setup Menu, 4-8
Spec key, 3-8
SPEC key, 4-38
Special Functions Menu, 4-12
Specifications, 1-12
Confidence Levels, 1-12
uncertainty, checking, 4-38
Using, 1-12
Standard Equipment, 2-3
State transitions, operating, 5-43
STATE? remote command, 5-40
Status Register Summary, 5-45