GE Multilin D20E - Daisy-Chaining D20 E Modules

138 pages

To Next Page

To Previous Page

82 GE INFORMATION D20E ETHERNET I/O MODULE INSTRUCTION MANUAL

CHAPTER 5: CONNECTING TO DEVICES AND NETWORKS

Daisy-chaining D20E modules

The daisy chaining of D20E Ethernet I/O Modules is shown in Figure 13.

Figure 14: Daisy chaining of D20E modules

D400

D20E-C

D20E-K

D20E-S

D20E-A

LAN #1

LAN #2

Main Page

Table of Contents3
Product Support8
Search GE Grid Solutions Technical Support Library8
Contact GE Grid Solutions Technical Support9
GE Grid Solutions Address9
Product Returns9
About this Document10
Example Module Being Configured and Monitored11
Additional Documentation11
GE Grid Solutions and Alstom Product Naming11
Form C Point References11
How to Use this Manual12
Safety Words and Definitions12
Comparing D20E to D.20 I/O Module Operation15
Safety Precautions15
High Voltage15
Protective Earth Ground16
Terminal Blocks TB1 and TB216
Warning Symbols17
Operating Environment17
Cyber Security Precautions17
Hardware Overview18
Configure Device Firmware19
Dapserver Studio Device Configuration Tool19
Terminal Emulator19
Data Communications19
DNP3 Server20
Ordering Guides21
Specifications24
Testing and Certification30
Approvals30
Tests and Standards30
Rohs Compliance31
Storage Recommendations32
Storage Conditions32
Installing the D20E Module33
Configuring the D20E Firmware34
Start Dapserver Studio38
Change D20E Module IP Address39
Dapserver Studio Sync Project41
Working with Projects41
Create a Project42
Open a Project45
Import an Existing Project from a Folder45
Import an Existing Project from a Device46
Save a Project46
Delete a Project47
Configuring D20E Modules47
Configure NTP Time Sync48
Change an Existing User's Password49
Change an Existing User's Permissions51
Configuring Points53
Digital Input Points53
Single and Double Digital Input53
COS and SOE54
Two Level Filtering54
Debounce Filter Period54
Chatter Filter (Oscillation Suppression)54
Digital Input Status Change Report as Counter Value55
Digital Input Point Quality Flag55
Digital Input Configuration Settings55
Double Digital Input Configuration Procedure57
Counter Points58
Analog Input Points61
Analog Value Type61
Analog Report Deadband61
Analog Alarm Threshold, Hysteresis and Qualification Period61
Analog Input Point Quality Flag62
Analog Input Configuration Settings62
Analog Input Configuration Procedure66
Control Output Points67
Control Output Type67
Control Output Point Quality Flag68
Control Output Point Configuration Settings68
Check Operation of the D20E71
Operation of Control Output Points71
Check the D20E System Status71
Access the Event Log71
Make D20E Device Setting Changes72
Mounting a D20E Module73
Required Clearances73
Rack Mounting Procedure74
Connecting to Devices and Networks76
Set up the Console Port76
Network Data Communication77
Network Address Setting and or Modification77
Daisy-Chaining D20E Modules80
Preliminary Power up and Test81
Preliminary Power-Up and Test Procedure83
Remote/Local Switch87
Trip/Close Control Outputs87
Form C Control Outputs88
Raise/Lower Control Outputs88
DPST Control Outputs88
D20E-S Digital Inputs Module92
D20E-C Combination Inputs and Outputs Module94
D20E-C Module Digital Inputs95
D20E-C Module Analog Inputs95
D20E-C Module Control Outputs96
Powering-Up and Testing a D20E Module98
Using the D20E Module101
Leds Common to All D20E Module Types102
Module Remote/Local Switch102
Terminal Block Connector Summary102
D20E-K Module Front Panel103
D20E-K Leds103
Remote/Local Switch103
D20E-K Connectors103
Operate a Raise/Lower DO Point104
D20E-A Module Front Panel105
D20E-A Leds105
D20E-A Connectors105
D20E-S Module Front Panel106
D20E-S Leds106
D20E-S Connectors106
D20E-C Module Front Panel107
D20E-C Leds107
Remote/Local Switch107
D20E-C Connectors107
Maintaining a D20E Module Firmware108
Fuse Replacement112
Performing Periodic Inspection112
Preventative Maintenance112
Rebooting the D20E112
DIP Switch Settings113
Firmware Update114
Clock Setting114
Time Synchronization114
Removing the D20E from Service115
Device Disposal116
Remove Configuration Data on a PC116
Dapserver Studio120
Main Window121
Project Configuration Window122
Window Title Bar122
Menu Bars123
Main Workspace123
Task Bar123
D20E Module Dnp3 Server Profile125

GE Multilin D20E - Daisy-Chaining D20 E Modules

Table of Contents

Related product manuals