Honeywell UDC2300 User Manual

vi UDC2300 Controller Product Manual 12/00
12.2.24 CSRATO (COMPUTER SETPOINT RATIO)...............................................................129
12.2.25 CYC T1 or CT1 X3 (CYCLE TIME - HEAT)................................................................129
12.2.26 CYC2T2 or CT2 X3 (CYCLE TIME2 - COOL).............................................................130
12.2.27 DBAND (DEADBAND) .................................................................................................130
12.2.28 DECMAL (DECIMAL POINT LOCATION).................................................................130
12.2.29 DI COM (DIGITAL INPUT COMBINATIONS) ...........................................................131
12.2.30 DIG IN (DIGITAL INPUT).............................................................................................131
12.2.31 DISPLAY (SINGLE DISPLAY DEFAULT)..................................................................133
12.2.32 EMISS (EMISSIVITY) ...................................................................................................133
12.2.33 ENDSEG (END SEGMENT)..........................................................................................133
12.2.34 EUHRDN (RATE DOWN VALUE)...............................................................................133
12.2.35 EUHRUP (RATE UP VALUE).......................................................................................133
12.2.36 FAILSF (FAILSAFE OUTPUT VALUE).......................................................................134
12.2.37 FILTR1 (INPUT 1 FILTER) ...........................................................................................134
12.2.38 FILTR2 (INPUT 2 FILTER) ...........................................................................................134
12.2.39 FINLSP (SINGLE SETPOINT RAMP FINAL SETPOINT)..........................................134
12.2.40 FREQ (POWER LINE FREQUENCY)...........................................................................135
12.2.41 FSMODE ( FAILSAFE MODE).....................................................................................135
12.2.42 FUZZY (FUZZY OVERSHOOT SUPPRESSION)........................................................135
12.2.43 HYST (HYSTERESIS - OUTPUT RELAY ONLY) ......................................................135
12.2.44 I MIN or I RPM (RESET - INTEGRAL TIME)..............................................................136
12.2.45 I2 MIN or I2 RPM (RESET2 - INTEGRAL TIME)........................................................136
12.2.46 INCRMT (TIME COUNT INCREMENT) .....................................................................136
12.2.47 IN1 HI (INPUT 1 HIGH RANGE VALUE)....................................................................137
12.2.48 IN1 LO (INPUT 1 LOW RANGE VALUE) ...................................................................137
12.2.49 IN1TYP (INPUT 1 ACTUATION TYPE)......................................................................138
12.2.50 IN2 HI (INPUT 2 HIGH RANGE VALUE)....................................................................139
12.2.51 IN2 LO (INPUT 2 LOW RANGE VALUE) ...................................................................139
12.2.52 IN2TYP (INPUT 2 ACTUATION TYPE)......................................................................140
12.2.53 L DISP (DISPLAY FOR TIMER OPTION) ...................................................................140
12.2.54 LNGUAG (LANGUAGE)...............................................................................................140
12.2.55 LOCK (LOCKOUT)........................................................................................................141
12.2.56 LOOPBACK (LOCAL LOOPBACK TEST)..................................................................141
12.2.57 LSP’S (LOCAL SETPOINT SOURCE) .........................................................................141
12.2.58 MANRST (MANUAL RESET) ......................................................................................142
12.2.59 MINRPM (RESET UNITS).............................................................................................142
12.2.60 OUTALG (OUTPUT ALGORITHM).............................................................................142
12.2.61 OUT Hi (HIGH OUTPUT LIMIT)..................................................................................143
12.2.62 OUT Lo (LOW OUTPUT LIMIT) ..................................................................................143
12.2.63 PARITY (PARITY).........................................................................................................143
12.2.64 PB or GAIN (PROPORTIONAL BAND or GAIN)........................................................144
12.2.65 PB 2 or GAIN 2 (PROPORTIONAL BAND 2 or GAIN 2)............................................144
12.2.66 PBorGN (PROPORTIONAL BAND UNITS) ................................................................145
12.2.67 PERIOD (TIMEOUT PERIOD)......................................................................................145
12.2.68 PG END (PROGRAM TERMINATION STATE)..........................................................145
12.2.69 PIDSET (NUMBER OF TUNING PARAMETER SETS) .............................................146
12.2.70 PVSTRT (PV START)....................................................................................................147
12.2.71 PWROUT (THREE POSITION STEP CONTROL OUTPUT START-UP MODE).....147
12.2.72 PWR UP (POWER UP CONTROLLER MODE RECALL) ..........................................148
12.2.73 RATE T (RATE TIME)...................................................................................................148

Honeywell UDC2300 Specifications

General

Brand	Honeywell
Model	UDC2300
Category	Controller
Language	English