JCM TAIKO - Page 39

To Next Page

To Previous Page

Chapter

Specifications

TAIKO Service Manual

2-1. Specifications

2-2. Connector

2-3. Interface Circuit

2-4. External Dimensions

2-5. DIP Switch Settings

Issue: 10/2007

4045-SME-002J

Main Page

Default Chapter9
- Table of Contents9
- Names of Parts17
- Product Specifications18
- General Specifications18
- Basic Specifications18
- Electrical Specifications18
- Environmental Specifications18
- Installation Specifications19
- Connector19
- Interface Connector X4:Serial(ID-003)/Mdb/Pulse/Cctalk Specification19
- 7-2-1-1.Interface Connector Pin Assignment20
- X4:Serial(ID-003)/Mdb/Pulse/Cctalk Specification20
- Interface Connector 01:Parallel(ID-001) Specification21
- 01:Parallel(ID-001) Specification21
External Dimensions22
- External Dimensions When Installing Type1/Type2/Type3 Faceplate22
- External Dimensions When Installing Type5 Faceplate23
- DIP Switch Settings24
- Basic Settings24
- X4:Serial(ID-003)/Mdb/Pulse/Cctalk Specification24
- Denomination Setting Mode25
- Encryption Code Initializing Setting Mode25
- Basic Settings 01:Parallel(ID-001) Specification26
- LED Pattern Setting Mode26
- Installation/Removal27
- Wiring30
- Recommended Parts30
- Recommended Parts X4:Serial(ID-003)/Mdb/Pulse/Cctalk Specification30
- Recommended Parts 01:Parallel(ID-001) Specification30
- Wiring Procedure31
- Clearing a Banknote Jam32
- Error Codes33
- Cleaning33
- Product Support34
- Japan Cash Machine Co.ltd. All Rights38
- Chapter 2 Specifications40
- Specifications40
  - Connector42
- ID-001 (Parallel) Specification43
- ID-001 (Parallel) Specification44
  - When Installing the Type1/Type2/Type3 Faceplate with TAIKO Unit49
  - When Installing the Type5 Faceplate with TAIKO Unit50
DIP Switch Setting51
- Basic Settings51
- X4: ID-003 (Serial)/ MDB/ Pulse/ Cctalk Specification51
- Basic Settings 01 : ID-001 (Parallel) Specification52
- Special Settings52
- Chapter 3 Installation / Operation56
Installation/Removal57
Wiring60
- Recommended Parts60
- Reccomended Parts60
- X4: ID-003(Serial)/ MDB/ Pulse/ Cctalk Specification60
- ID-001 (Parallel) Specification60
- Wiring Procedure61
- Chapter 4 Download / Adjustment63
Download63
- Requirements64
- Connecting Procecedure65
- Download Procedure66
- Writing Serial no67
Adjustment70
- Requirements70
- Adjustment Procedure71
Palm73
- Requirement73
- Installing File Converter (Pdbconven.exe)74
- Converting Software Program75
- Download Procedure76
Cloning78
- Required Items78
- Cloning Procedures79
Trouble Shooting80
- General Troubles81
- Chapter 5 Trouble Shooting / Maintenance80
Error Code80
- TAIKO Service Manual80
- Chapter 1 Introduction81
- Component Names81
  - Adjustment Troubles83
  - Communication Troubles84
Test Mode (Diagnostics)85
- DIP Switch Setting List85
- DIP Switch Test Procedure85
- Transport Motor Forward Rotation Test Procedure85
- Transport Motor Reverse Rotation Test Procedure86
- Aging Procedure86
- Solenoid Test Procedure87
- Accepting Test Procedure87
- Entrance Flapper Test Procedure88
- Exit Flapper Test Procedure88
Cleaning89
Maintenance Tool List90
Product Support93
- Chapter 6 Replacement94
Replacement of Faceplate Guide95
Replacement of CPU Board96
Replacement of MAG Board97
Replacement of Sensor Board98
Replacement of Encoder Board/Motor Unit102
Replacement of Solenoid103

JCM TAIKO - Page 39

Table of Contents

Related product manuals