JCM TAIKO - Japan Cash Machine Co.ltd. All Rights

104 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Copyright 2007 Japan Cash Machine Co.Ltd. All rights reserved. 08.05 4045-IGE-001A

c

Table of Contents

Default Chapter9
- Table of Contents9
- Names of Parts17
- Product Specifications18
- General Specifications18
- Basic Specifications18
- Electrical Specifications18
- Environmental Specifications18
- Installation Specifications19
- Connector19
- Interface Connector X4:Serial(ID-003)/Mdb/Pulse/Cctalk Specification19
- 7-2-1-1.Interface Connector Pin Assignment20
- X4:Serial(ID-003)/Mdb/Pulse/Cctalk Specification20
- Interface Connector 01:Parallel(ID-001) Specification21
- 01:Parallel(ID-001) Specification21
External Dimensions22
- External Dimensions When Installing Type1/Type2/Type3 Faceplate22
- External Dimensions When Installing Type5 Faceplate23
- DIP Switch Settings24
- Basic Settings24
- X4:Serial(ID-003)/Mdb/Pulse/Cctalk Specification24
- Denomination Setting Mode25
- Encryption Code Initializing Setting Mode25
- Basic Settings 01:Parallel(ID-001) Specification26
- LED Pattern Setting Mode26
- Installation/Removal27
- Wiring30
- Recommended Parts30
- Recommended Parts X4:Serial(ID-003)/Mdb/Pulse/Cctalk Specification30
- Recommended Parts 01:Parallel(ID-001) Specification30
- Wiring Procedure31
- Clearing a Banknote Jam32
- Error Codes33
- Cleaning33
- Product Support34
- Japan Cash Machine Co.ltd. All Rights38
- Chapter 2 Specifications40
- Specifications40
  - Connector42
- ID-001 (Parallel) Specification43
- ID-001 (Parallel) Specification44
  - When Installing the Type1/Type2/Type3 Faceplate with TAIKO Unit49
  - When Installing the Type5 Faceplate with TAIKO Unit50
DIP Switch Setting51
- Basic Settings51
- X4: ID-003 (Serial)/ MDB/ Pulse/ Cctalk Specification51
- Basic Settings 01 : ID-001 (Parallel) Specification52
- Special Settings52
- Chapter 3 Installation / Operation56
Installation/Removal57
Wiring60
- Recommended Parts60
- Reccomended Parts60
- X4: ID-003(Serial)/ MDB/ Pulse/ Cctalk Specification60
- ID-001 (Parallel) Specification60
- Wiring Procedure61
- Chapter 4 Download / Adjustment63
Download63
- Requirements64
- Connecting Procecedure65
- Download Procedure66
- Writing Serial no67
Adjustment70
- Requirements70
- Adjustment Procedure71
Palm73
- Requirement73
- Installing File Converter (Pdbconven.exe)74
- Converting Software Program75
- Download Procedure76
Cloning78
- Required Items78
- Cloning Procedures79
Trouble Shooting80
- General Troubles81
- Chapter 5 Trouble Shooting / Maintenance80
Error Code80
- TAIKO Service Manual80
- Chapter 1 Introduction81
- Component Names81
  - Adjustment Troubles83
  - Communication Troubles84
Test Mode (Diagnostics)85
- DIP Switch Setting List85
- DIP Switch Test Procedure85
- Transport Motor Forward Rotation Test Procedure85
- Transport Motor Reverse Rotation Test Procedure86
- Aging Procedure86
- Solenoid Test Procedure87
- Accepting Test Procedure87
- Entrance Flapper Test Procedure88
- Exit Flapper Test Procedure88
Cleaning89
Maintenance Tool List90
Product Support93
- Chapter 6 Replacement94
Replacement of Faceplate Guide95
Replacement of CPU Board96
Replacement of MAG Board97
Replacement of Sensor Board98
Replacement of Encoder Board/Motor Unit102
Replacement of Solenoid103

Related product manuals

Preview: JCM TBV Series

JCM TBV-100 FSH

JCM TBV-100 FLD

Preview: JCM TAIKO PUB-7/11

JCM TAIKO PUB-7/11

Preview: JCM iVIZION

Preview: JCM DBV Series

Preview: JCM VEGA Series

JCM VEGA Series

Preview: JCM ivision series

JCM ivision series

Preview: JCM iPRO-100-SH2-RC

JCM iPRO-100-SH2-RC

JCM DBV-400 Series