JDS Uniphase DSAM-3500 User Manual

List of Figures
xxii DSAM Help User Guide Revision 001
Figure 152 Measure Mode – Enable/Disable Channels . . . . . . . . . . . . . . . . . 167
Figure 153 Measure Mode – Basic Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Figure 154 Measure Mode – Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Figure 155 Measure Mode – Downstream Plans. . . . . . . . . . . . . . . . . . . . . . . 171
Figure 156 Measure Mode – Select Tilt Channels. . . . . . . . . . . . . . . . . . . . . . 172
Figure 157 Measurement Mode – Basic Tab: Constellation . . . . . . . . . . . . . . 175
Figure 158 Measure Mode – Constellation . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Figure 159 Constellation – Thermal (system) Noise . . . . . . . . . . . . . . . . . . . . 177
Figure 160 Constellation – Phase Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Figure 161 Constellation – Coherent Interface . . . . . . . . . . . . . . . . . . . . . . . . 177
Figure 162 Constellation – Gain Compression . . . . . . . . . . . . . . . . . . . . . . . . 178
Figure 163 Constellation – I/Q Imbalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Figure 164 Measure Mode – Constellation Refresh Rates . . . . . . . . . . . . . . . 179
Figure 165 Measure Mode – Basic Tab: FDR . . . . . . . . . . . . . . . . . . . . . . . . . 181
Figure 166 Measure Mode – FDR Locate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Figure 167 Configure – FDR Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Figure 168 Measure Mode – Basic Tab: Return QAM Generator . . . . . . . . . . 185
Figure 169 Measure Mode – Return QAM Generator . . . . . . . . . . . . . . . . . . . 186
Figure 170 Measure Mode – Basic Tab: QAM Ingress . . . . . . . . . . . . . . . . . . 188
Figure 171 Measure Mode – QAM Ingress . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Figure 172 Measure Mode – Basic Tab: Hum . . . . . . . . . . . . . . . . . . . . . . . . . 191
Figure 173 Measure Mode – Hum Analysis. . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Figure 174 Measure Mode – Basic Tab: DQI. . . . . . . . . . . . . . . . . . . . . . . . . . 193
Figure 175 Measure Mode – DQI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Figure 176 Measure – Return Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Figure 177 Measure Mode – Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Figure 178 Measure Mode – Level Channel . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Figure 179 Measure – DQI Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Figure 180 Save a File screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Figure 181 AutoTest – Edit Location Settings . . . . . . . . . . . . . . . . . . . . . . . . . 199
Figure 182 Create a New Work Folder screen . . . . . . . . . . . . . . . . . . . . . . . . 200
Figure 183 Measure Mode – Service Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Figure 184 Configure Mode – Other Settings . . . . . . . . . . . . . . . . . . . . . . . . . 205
21128026 R001 DSAM Help User Guide.book Page xxii Thursday, February 5, 2009 2:02 PM

JDS Uniphase DSAM-3500 Specifications

General

Brand	JDS Uniphase
Model	DSAM-3500
Category	Measuring Instruments
Language	English