Keysight MP4300 Series

To Next Page

To Previous Page

Do not ship MPS mainframes with the power modules installed. Remove all power

modules from the mainframe before returning the instrument.

Keysight suggests that you always insure shipments.

Keysight MP4300 Series Operating and Service Guide 185

7 Service and Maintenance

Main Page

Table of Contents3
Legal and Safety Information7
Legal Notices7
Safety and Regulatory Symbols9
Safety Notices10
Quick Reference13
Introduction to the Instrument14
Modular Power System at a Glance14
Front Panel at a Glance15
Rear Panel at a Glance16
Front Panel Display at a Glance17
Front Panel Keys at a Glance19
Front Panel Menu Reference20
Command Quick Reference21
Model Features and Options28
Model Features28
Options/Accessories28
Specifications and Characteristics29
Power Module Specifications and Characteristics29
Power Module Output Quadrants31
Mainframe Characteristics31
Outline Diagram33
Installing the Instrument35
Before Installation or Use36
Inspect the Unit36
Check for Items Supplied36
Review Safety Information36
Observe Environmental Conditions37
Provide Adequate Air Flow37
Moving Instruments37
Stacking Instruments37
Rack Mounting Accessories37
Installing the Mainframe38
Power Module Installation38
Bench Installation40
AC Mains Connections41
AC Mains Considerations41
Power Cable Connections41
Output Connections44
Wiring Considerations44
Single Load Connections46
Multiple Load Connections47
Remote Sense Connections48
Paralleled Channel Connections50
Parallel Connections50
Interface Connections52
LAN Connections - Site and Private52
USB Connections53
Getting Started55
Using the Front Panel56
Turn the Unit on56
Set the Output Voltage57
Set the Output Current58
Set the Output Mode and Priority59
Enable the Output60
Remote Interface Configuration61
Introduction61
LAN Configuration61
Modifying the LAN Settings62
GPIB/USB Configuration63
Using the Web Interface64
Using Telnet67
Using Sockets67
Using the Modular Power System69
Fixed Mode Operation70
Set the Operating Mode70
Set the Output Priority Mode71
Set the Output Voltage71
Set the Output Current72
Enable the Output72
Priority Mode Tutorial73
SAS Operation76
Introduction76
Compensation Modes77
Programming a Curve79
Programming a Table81
Reference Information83
Current Sinking Operation85
Current Sinking85
Regenerative Operation85
Programming Output Protection86
Introduction86
Set the Over-Voltage Protection87
Making Measurements88
Average Measurements88
Programming the Digital Port89
Digital Control Port89
Bi-Directional Digital I/O89
Digital Input90
Fault Output91
Inhibit Input91
System-Related Operations92
Instrument Identification92
Error Queue92
Instrument State Storage92
Password Protection93
SCPI Programming Reference95
Related Software96
SCPI Introduction97
Introduction97
Keywords97
Queries98
Command Separators and Terminators98
Syntax Conventions99
Parameter Types100
Device Clear101
Commands by Subsystem102
Current Subsystem106
Digital Subsystem113
Fetch Subsystem115
Function Command116
Hcopy Subsystem117
IEEE-488 Common Commands118
LXI Subsystem123
Measure Subsystem124
Memory Subsystem125
Output Subsystem128
[Source] Subsystem131
Status Subsystem132
System Subsystem139
Voltage Subsystem142
Status Tutorial147
Status Registers147
EDP Status Register147
UNR Status Register148
Standard Event Status Group148
Questionable Status Groups149
Operation Status Group150
Frame Status Group150
Status Byte Register151
Error and Output Queues152
Status Diagram152
Reset State (*RST)153
SCPI Error Messages156
E4360A Compatibility164
Verification and Calibration167
Test Equipment and Setups168
Test Equipment168
Measurement Setups168
Performance Verification170
Introduction170
Verification Setups171
Test Considerations172
Verification Procedure172
Instrument Calibration175
Introduction175
Calibration Interval176
Calibration Setups176
Test Considerations176
Calibration Procedure177
Test Record Forms - MPS Family180
Service and Maintenance183
Introduction184
Repair Service Available184
Before Returning the Unit184
Repackaging for Shipment184
Self-Test Procedure186
Power-On Self-Test186
User-Initiated Self-Test186
Calibration Switches187
Accessing the Calibration Switch187
Switch Functions187
Battery Replacement188
Replacing the Battery188
Cleaning189
Cleaning the Outside189
Cleaning the Filter189
Disassembly191
Electrostatic Discharge (ESD) Precautions191
Tools Required191
Remove Maintenance Cover191
Access the Calibration Switches and the Battery192
Index195

Keysight MP4300 Series - Page 185

Table of Contents

Related product manuals