Korg Krome - Writing and Saving Data; Saving Procedures

Introduction to the KROME
12
Writing/saving
Afterediting,youshouldwriteorsaveyourchangesas
necessary.
Forexampleifyou’veeditedaprogram,yourchanges
willbelostifyouselectanotherprogramorturnoff
thepower.Thesameappliestoacombination.
SettingsyoueditinGlobalmodeandsongswillbe
rememberedaslongasthepowerison,butyour
changeswillbelostwhenyouturnoffthepower,
unlessyouwritethesechangesintomemory.
•YoucanwriteorsavebypressingtheWRITE
buttontwice.
FormoredetailsontheWriteoperations,seethe
followingpages.
• Programs→ p.30
• Combinations→ p.47
•Effectpresets→ PG
p.67
•Globalsettings(pages0–4)→ p.116
•Dr
umkits→ p.116
•Userarpeggiopattern→ p.116
•UserDrumTrackpatterns→ p.103
Preset/userDrumTrackpatternsaresavedin
internalmemoryevenwhenthepoweristurned
off.PatternsthatyoucreateinSequencermodecan
beconvertedintouserDrumTrackpatternsand
savedininternalmemory.
•Usertemplatesongs→ PG p.164
Preset/usertemplate
songsaresavedininternal
memoryevenwhenthepoweristurnedoff.Track
settingsandeffectsettingsofasongyoucreatecan
besavedininternalmemorybyusingthemenu
commandSaveTemplateSong.
•Fordetailsonwritingtointernalmemory→ p.115
Refertothefollowingpagesformoreinformation
aboutsaving.
• Savinga
song→ p.75
• Savingtomedia(Media–Save)→ p.118
Note: OntheKROME,theactionofwritingtointernal
memoryiscalled“Write,”andtheactionofsavingto
anSDcarddeviceiscalled“Save.”
Assigning a name (renaming)
Youcaneditthenameofaneditedprogram,
combination,song,drumkit,orarpeggiopattern.
Youcanalsochangethenamesoftheprogramand
combinationcategories.
Fordetails,pleasesee“Editingnames”onpage 117.
Shortcuts
Selecting a GM bank program
• BankGM:Holddownthe0numerickeyandpress
–.
•Banksg(1)–g(9):Holddownthe0numerickeyand
press1–9.
• Bankg(d):Holddownthenumerickey0andpress
(.).
Moving between pages within a mode
•ByholdingdownthePAGEbuttonandpressinga
numerickey0–9youcanjumptothe
correspondingpage.
Access the menu commands in each page (up
to ten items)
•ByholdingdowntheENTERbuttonandpressinga
numerickey0–9.
Input note number values or velocity values
•Whileholdingdowntheeditcellinthedisplay,
pressanoteonthekeyboard.
Alternatively,selecttheeditcellinthedisplay,and
thenholddowntheENTERbuttonandpressanote
onthekeyboard.
Note: YoucanalsouseaMIDInote‐onmessageinstead
ofthekeyboard.
Note: Whileadialogboxisdisplayed,theENTER
buttonwillperformthesamefunctionastheOK
button.Thismeansthatyoucan’tusethismethodto
enteranotenumberorvelocityvalueinadialogbox
thatcontainsanOKbutton.
Specifying the location in a song
InSequencermode,setsthecurrentlocationasthe
Location(equivalenttotheSetLocationmenu
command)
•HolddowntheENTERbuttonandpressthe
LOCATE()button.
ENTER button
•Whileadialogboxisdisplayed,thisbutton
performsthesamefunctionastheOKbutton.
EXIT button
Thisbuttonmakesiteasytoreturntothemainpageof
thecurrentmode:
1. Pressitoncetogotothepreviouslyselectedtabon
themainP0page.
2. PresstheEXITbutton.Youwillmovetothe
previouslyselectedparameteroftheP0toppage
(Prog:Main,Combi/Seq:ProgramT01–08).
3. PresstheEXITbutton.Youwillmovetothe
followingparameteroftheP0toppage.
Prog:ProgramSelect
Combi:CombinationSelect
Seq:SongSelect