Korg Krome

Using Effects
80
10. AccesstheP8:Routing/IFX–InsertFXSetuppage,
andedittheparametersoftheinserteffectyou
selected.
PresstheIFX1–5tabsandedittheparameters.
Effect1On/Off:Turnstheinserteffecton/off.Thisis
linkedwiththeon/offsettingontheInsertFXSetup
page.
P(EffectPreset):Selectsaneffectpreset.TheKROME’s
internalmemorycontains“effectpresets”whichare
parametersettingsforeacheffectfrom001:Stereo
Compressorthrough193:EarlyReflections.
Effectparametersyoueditaresavedaspartofeach
program,buteffectpresetsallowyoutosaveandrecall
yourfavoriteparametersettingsforeacheffect.If
you’vecomeupwithaneffectsettingyoulike,us
ethe
menucommandWriteFXPresettosaveitasapreset
sothatyoucaneasilyrecallitinadifferentprogramor
mode.
Fordetailsontheparametersofeacheffect,see
page 251andfollowingintheParameterGuide.
Double-size effects
Double‐sizeeffects(172:St.MltbandLimiter–193:
EarlyReflections)usetwiceasmuchspaceasother
effects.
Youcanusedouble‐sizeeffectsforinserteffectsIFX1–
IFX4andmastereffectMFX1.However,becauseit
takesuptwounitsofeffectspower,thenext‐numbered
effectwillbeunavailable.Forexample,ifyou’ve
selectedadouble‐sizeeffe
ctforIFX1,youwon’ tbeable
touseIFX2.Ifyou’veselectedadouble‐sizeeffectfor
MFX1,youwon’ tbeabletouseMFX2.
Anexampleofwhenadouble‐sizeeffectisselectedforIFX1
andIFX4
Master effects
11. Theinputlevelstothemastereffectsaresetby
theSend1,2levels(step3or9).IfSend1,2are
zero,themastereffectswillnotapply.Send1
correspondstoMFX1,andSend2correspondsto
MFX2.
12. AccesstheProgP9:MFX/TFX/LFO–Routingpage.
13. InMFX1andMFX2,selec
tthetypeofeachmaster
effect.
Theprocedureisthesameaswhenselectinganins
ert
effect(seestep6).
Note: Youcanonlyselectadouble‐sizeeffectfor
MFX1.Fordetails,pleasesee“Double‐sizeeffects,”
above.
14. PresstheOn/Offbuttontoturnonthemaster
effect.
Eachtimeyoupressthisbutton,themastereffectwill
toggleon/off.WhenOff,theoutputofthemastereffect
willbemuted.
15. UseReturn1
andReturn2toadjusttheoutput
levelsofthemastereffects.
Note: Foreacheffect,theWetvalueoftheWet/Dry
parameteristheoutputleveloftheeffect.Thereturn
valueismultipliedwith this(“Return”=127willbe
x1.0)todeterminetheactualoutputlevelofthemaster
effect.
16. SelecttheMFX1andMFX2pages,andsetthe
parametersforeachselectedeffect.
Fordetailsonthe“ProgramEffectssettings”step10.
Total Effect
17. IfyouuseBus(IFX/Output)SelecttochooseL/R
astheoscillatoroutput,orifyousetthepost‐IFX
BustoL/R,thesignalwillbeinputtothetotal
effect.
Theoutputfromthemastereffectisinputtothetotal 
effectviatheReturn1andReturn2settingsoftheProg
P9:MFX/TFX/LFO–Routingpage.
Afterbeingprocessedthroughthetotaleffect,the
signalisoutputfromtheAUDIOOUTPUTL/MONO
andRoutputs.
18. AccesstheProgP9:MFX/TFX/LFO–Routingpage.
19. ChoosethedesiredtotaleffectforTFX.The
procedureisthesameaswhenselectinganinsert
effect.(Seestep6)
Youcan’tuseadouble‐sizeeffectasthetotaleffect.
Fordetails,pleasesee“Double‐sizeeffects,”above.
P (Eect Preset)
Eect Parameters
Eect On/O
Wet/Dry