Korg Krome

Routing effect settings Using effects in Combinations and Songs
81
20. PresstheOn/Offbuttontoturnthetotaleffecton.
Thetotaleffectwilltoggleon/offeachtimeyoupress
thebutton.IfthisisOff,theresultwillbethesameasif
000:NoEffectisselected.Theinputsoundwillbe
outputwithoutbeingprocessedbythetotaleffect.
21. AccesstheTFXpage,andedittheparametersof
eacheffecttoadjustthefinalsoundasdesired.
Fordetailsonthe“ProgramEffectssettings”,seestep
10.
Using effects in Combinations
and Songs
InCombination,andSequencermodes,youcan
specifytheroutingofeachtimbre/tracktotheinsert
effects,mastereffectsandtotaleffect.Thesesettings
areadjustedinthesamewayineachofthesemodes.
WewillbeusingtheexampleofCombinationmodein
ourexplanationhere.
Routing
1. AccesstheCombiP8:Routing/IFX–RoutingT01–
08page.
2. Use“Bus(IFX/Output)Select”tospecifythebus
whereeachtimbrewillbeoutput.ChooseIFX1if
youwanttosendtheoutputofatimbretoinsert
effect1.
Therouting,inserteffects,andchainsettingsare
showngraphicallyontheupperpartofthepa
ge.In
thisexample,T01(timbre1)usesIFX1and2.T02uses
IFX2,T03uses
IFX3and4,T02andT05useIFX4,and
T06andT07useIFX5.
3. UseSend1andSend2tospecifythesendlevelof
eachtimbretothemastereffects.
ThiscanbesetonlyifBus(IFX/Output)Selectissetto
L/RorOff.
Note: Theactualsendlevelisdeterminedby
multiplyingthisbytheSend1orSend2settingsfor
oscillators1and2withintheprogramselectedbythe
timbre.IftheprogramparameterSend1orSend2is
setto0,theresultinglevelwillstillbe0evenifyou
raisethissendlevel.
IfBus(IFX/O
utput)SelectissettoIFX1–5,thesend
levelstothemastereffectsaresetbySend1andSend2
(InsertFXSetuppage)followingtheinserteffects.
4. PresstheFXControl1–8tabstoaccesstheFX
ControlT01–08pages.
Bus(IFX/Output)SelectisthesameasintheRouting
T01–08page.Youcansetitfromeitherpage.
FXControlBussendstheoutputofthetimbretoanFX
Controlbus.Usethiswhenyouwanttheaudioinput
toaneffecttobecontrolledbyanothersound.There
aretwoFXControlbuses,whichgivesyouagreatdeal
offreedomforcontrollingeffectsfreely.Fordetails,
pleasesee“FXControlBuses”onpage 238ofthe
ParameterGuide.
Insert effects
5. AccesstheCombiP8:Routing/IFX–InsertFX
Setuppage.
6. SelectaninserteffectinIFX1–5andeditthe
settings.
7. AccesstheIFX1–5pagestoedittheindividual
effectparameters.
Thesesettingscanbeadjustedinthesameway.(See
page 79.)
YoucanuseMIDItocontroldynamicmodulation
(Dmod)foreacheffect,thepost‐IFXpan(CC#8),
andSend1andSend2levels.
Anasterisk“*”isshownattherightofCh01–Ch16
fo
rthechannelnumberoftracksroutedtoIFX.If
you’veroutedmultipletracksthathavedifferent
MIDIchannelsettings,thisspecifiesthechannel
onwhichtheywillbecontrolled.
Master effects and Total effect
Thesesettingscanbeadjustedinthesamewayason
page 80.
YoucancontroltheseeffectsviaMIDIonthe“Ctrl
Ch.”ThespecifiedMIDIchannelwillcontrol
dynamicmodulation(Dmod)fortheMasterand
TotalEffect.