Korg Krome

Arpeggiator function
86
Using knobs 1–4 to control the
arpeggiator
•Youcancontrolthearpeggiatorbypressingthe
SELECTbuttontoselectARPandthenturning
knobs1–4.
Adjusting the duration of the arpeggiated
notes
•Turnknob1toadjustthedurationofthe
arpeggiatednotes.
Rotatingtheknobtowardtheleftwillshortenthe
durationofthenotes,androtatingittowardthe
rightwilllengthenthedurationofthenotes.Atthe
centerposition(12o’clock),thenotelengthwillbe
asspecifiedbytheprogramparameter:Gate(Prog
P7:ARP/DT–ARPSetuppage).
Note: Theknobsettingissavedwhenyouwr
iteeach
program.
Note: ItiseffectivetousetheSELECTbuttontoselect
TONE,andthenadjustknob4(RELEASE).
Changing the dynamics of the arpeggiated
notes
•Turnknob2toadjustthedynamicsofthe
arpeggiatednotes.
Turningtheknobtowardtheleftwillmakethe
notessofter,andturningittowardtherightwill
makethenotesstronger.Whentheknobisinthe
centerposition(12o’clock),thevalueofthepro‐
gramparameterVelocity(ProgP7:ARP/DT–Arp
Setuppage)willbeused.
Note: Thestateoftheknobissave
dwhenyouwrite
theprogram.
Note: ItiseffectivetousetheSELECTbuttontoselect
TONE,andthenadjustknobs1(CUTOFF),2
(RESONANCE),and3(EGINT).
Adding a shuffle feel to the arpeggio pattern
•Ifyouturnknob3,thetimingofthearpeggiated
notesoneven‐numberedbeatswillbeshifted
forwardorbackward.
Turningtheknobtowardtheleftwillspeedupthe
timingoftheeven‐numberedbeats.Whentheknob
isinthecenterposition(12o’clock),thetimingwill
beasspecifiedbytheprogramparameterSwing
(GlobalP6:ArpeggioPattern‐Setuppage).
Changing the number of steps in the
arpeggio pattern
•Byturningknob4(STEP),youcanchangethe
numberofstepsinthearpeggiopattern.
Turningtheknobtowardtheleftwillshortenthe
patternlength(“Length”)byhalf.Turningtheknob
towardtherightwillshortentheintervalofthe
arpeggiatednotes(“Resolution”)byhalf.Whenthe
knobisinth
ecenterposition(12o’clock),thepat‐
ternwillbeasspecifiedbytheparametersLength
andResolution(GlobalP6:Arpeggi
oPattern–
Setuppage).
Ifthearpeggiopatternselectedby“Pat(Pattern
Select)”isoneofthepresetarpeggiopatternsP0–
P4,turningtheknobswillnotproduceany
change.Theseadjustmentsareavailableonlyifa
userarpeggiopatternU0000(INT)–U1027(USER)
isselect
ed.
Note: Thestateoftheknobsissavedwhenyouwrite
theprogram.
Note: Dependingontheprogramthat’sselected,using
knob4maynotproduceanyeffect.
Selecting an arpeggio pattern and
specifying its function
IntheProgP0:Play–Arpeggiatorpageyoucanselect
anarpeggiopatternandspecifyhowthearpeggiator
willfunction.
•InProgP0:Play,presstheARPtabtoaccessthe
ProgP0:Play–Arpeggiatorpage.
Selecting an arpeggio pattern
Anarpeggiopatterncanbeselectedfrompreset
arpeggiopatternsP0–P4anduserarpeggiopatterns
U0000(INT)–U1027(USER).Thefactorysettings
U0000(INT)–U0899(INT),U0900(USER)–U1027(USER)
containawidevarietyofpreloadeduserarpeggio
patterns.
•ChoosePattern,andusetheVALUEdial,INC/DEC
buttons,andpopupmenutoselectanarpeggio
pattern.
Userarpeggiopatternscanalsobeselectedbyusing
thenumerickeys0–9toinputthepatternnumber
andthenpressingtheENTERbutton.
P0: UP
UP