Kyocera FS-C8520MFP - Page 375

2MY/2MZ-2
No. Content
Check procedure & check point
Remark 1
TASKalfa 256ci/FS-C8525MFP, TASKalfa 206ci/FS-C8520MFP,
TASKalfa 306i/FS-6530MFP, TASKalfa 256i/FS-6525MFP
F25X
An error is detected at the
Network management section
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check
function.
3) Replace the main board and check function.
4) Retrieve the USBLOG and contact the Service Administratuve Division.
(or retrieve the packet capture data depending on the reult of analysis)
(*1) For the HDD standard model only.
*This may be owing to the
users network environment.
F26X
F27X
F28X
F29X
F2AX
F2B
X
F2C
X
F2D
X
F2E
X
F2F
X
F30
X
F31
X
F32X
F33X
An error is detected at the
Scan management section
1) Check connection of the harness (Scan/DP board - main board) and connectors and
check function.
2) Format the HDD and check function. (U024 FULL formatting) (*1)
3) Execute the U021 Memory initializing to initialize the controller backup memory and check
function.
4) Replace the Scan/DP board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
(*1) For the HDD standard model only.
[Main-Scan Interface]
Main board: YC112, YC113
CCD PWB: YC1
LED PWB: YC1
F34X
An error is detected at the
Panel management section
1) Check connection of the harness (Panel board - main board) and connectors and check
function.
2) Format the HDD and check function. (U024 FULL formatting) (*1)
3) Execute the U021 Memory initializing to initialize the controller backup memory and check
function.
4) Replace the panel board and check function. (*2)
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
(*1) For the HDD standard model only.
(*2) For the models separating the panel/main PWBs.
[Main-Panel Interface]
Main board: YC100, YC101, YC102
Panel board: YC1, YC2, YC3
F35X
An error is detected at the
Print control section
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check
function.
3) Replace the main board and check function.
4) Replace the HDD and check function. (*1)
5) Retrieve the USBLOG and contact the Service Administrative Division.
(*1) For the HDD standard model only.
An error is detected at the
Network control section
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check
function.
3) Replace the main board and check function.
4) Retrieve the USBLOG and contact the Service Administratuve Division.
(or retrieve the packet capture data depending on the reult of analysis)
(*1) For the HDD standard model only.
An error is detected at the
System management section
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check
function.
3) Replace the main board and check function.
4) Replace the HDD and check function. (*1)
5) Retrieve the USBLOG and contact the Service Administrative Division.
(*1) For the HDD standard model only.
2-4-15