10. Technologies MX-FR Series Modular Matrix Frames β User's Manual 159
ξ₯ξξξξξξξξ§ξ΄ξΉξξξξξξξξ
ξξξξξξξξξξξξξξ ξξ°ξ¨ξ§ξξξξξξξ
ξξξξξξξξξξξξξ
ξξξξξξ£EDID Management
ξξξξξξξξ£Understanding the EDID
ξΈξξξ ξ©ξξξξξξξξ ξ¨ξξξξξ
ξξ ξξξξξξξ€ξξ
ξξξξξ ξ¨ξ
ξξ
ξ ξξ©ξ¨ξξ¨ξξ ξξξ ξξξξ ξξ
ξξξξξξξ ξξξ ξξξξξξ
ξξ ξξξξξξξξ ξξξξξξξξξξξ ξΈξΊξ ξξξξξξ
projectors). It contains information about the capabilities of the display, such as supported resolutions,
refresh rates (these are called Detailed Timings), the type and manufacturer of the display device, etc.
After connecting a source to a display (DVI, HDMI, DP), the source reads out the EDID to determine the
resolution and refresh rate of the image to be transmitted.
EDID Communication
Most DVI computer displays have 128-byte long EDID structure. However, Digital Televisions and HDMI
ξξ
ξξ
ξξξξ ξξξξξξ
ξξξ ξξ
ξξ ξξ
ξξξ ξ
ξξξξξξξ ξξξξ ξξξξξξξ ξξξξξξ ξξξ ξξ
ξξξξξ ξ©ξξ©ξ¨ξξ¨ξ ξ
ξξξ ξξξ€ξξξξ ξξξ ξ§ξ©ξ₯ξ ξξ§ξξξξξξξξ
Electronics Association). This extension contains information about additional Detailed Timings, audio
capabilities, speaker allocation and HDMI capabilities. It is important to know that all HDMI capable devices
must have CEA extension, but not all devices with CEA extension are HDMI capable.
Common Problems Related to EDID
ξ΄ξξξξξξξξ ξ°ξ±ξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξ
ξξξξξξξξξξξξ
ξξ°ξξξξξξ
ξξξξξξξξξξξξ
ξξ»ξΉξΌξ«ξ₯ξξξξξξξξξξξξξ
LCD monitor, and an SXGA (1280x1024) projector. I would like to see the same image on the
ξξξξξξξξξ
ξξξξξξξξξξξξξξξξξξξ»ξξ
ξξξ©ξ¨ξξ¨ξξξξξξξξξξξξξξξξξξξξξξξξξ°ξξξξξξ
ξξξξξξξξξξ£ξ±
Solution: If you want to see the image on both displays, you need to select the resolution of the smaller
display (in this case SXGA), otherwise the smaller display may not show the higher resolution
image.
ξ΄ξξξξξξξξ ξ°ξξξξ
ξξξξξξ
ξξξξξξξξξ
ξξξξξξξξξξξξ©ξ¨ξξ¨ξξξξξ
ξξξξξξξξξξξξξξξξξξξξξ°ξξξξξξ
ξξξξξξξξξξξξξξξ
ξξξξ
ξξξξξξξξξξξ
ξξξξξξξξξξξξξξξξξξξξξξξξξ
ξξξξξξξ±
Solution: Some graphics cards and video sources read out the EDID only after power-up and later they do
ξξξξξξξξξξξξξ
ξξξ©ξ¨ξξ¨ξξξ
ξξξξξξξξξξ
ξξξξξξξ½ξξξξξξξξξξξξξξξξ
ξξξξξξξξξξξξξξξξξξξξ
ξξξξξξξξξ
ξξξξξξξξξξ
EDID again.
ξξξξξξξξ£Advanced EDID Management
Each DVI sink (e.g. monitors, projectors, plasma displays, etc...) must support the EDID data structure.
Source BIOS and operating systems are likely to query the sink using DDC2B protocol to determine what
pixel formats and interface are supported. DVI standard uses EDID data structure to identify the monitor type
and capabilities. Most DVI sources (VGA cards, set top boxes, etc.) will output DVI signal after accepting the
ξξξξξξξξξξξξξξξξξξ©ξ¨ξξ¨ξξξξξξξξ
ξξξξξξξξξξξξξξξ
ξξξξξξξ©ξ¨ξξ¨ξξξξ
ξξξξξξξ
ξξξξξξξξξξξξξξξξξξ©ξ¨ξξ¨ξξξξξξξξξξξξξξξξξξξξξξ
output DVI video signal.
Lightware devices provide the Advanced EDID Management function that helps system integration. The
built-in EDID Router can store and emulate factory pre-programmed- and User programmable EDIDs. The
EDID of the attached monitors or projectors for each output are stored in a non-volatile memory. This way
the EDID of a monitor is available when the monitor is unplugged or switched off.
ξ₯ξξξξ©ξ¨ξξ¨ξξξ
ξξξξξξξξξξ
ξξξξξξξξ
ξξξξξξξξξξξ₯ξξξξξξξ
ξξξξξ©ξ¨ξξ¨ξξξ
ξξξξξξξξξξξξξξξξξξξξξξ©ξ¨ξξ¨ξξξξξξξξξξξξξξξξξ
ξξξξ
ξξξξξ©ξ¨ξξ¨ξξξξξξ
ξξξξξξξξξξξξξξξξξξξξξ
ξξξξ
ξξξ
ξξξξξξξξξξξξξξξξξξξξξξξξξξξ
ξξξξξ©ξ¨ξξ¨ξξξξξξ
ξξξξξξξξͺξξξξξξ
ξξξξξξ
the Lightware device can be set up to emulate a sink device, which is connected to one of the outputs. In
this case, the EDID automatically changes, if the monitor is replaced with another display device (as long as
it has a valid EDID).
EDID is independently programmable for all inputs without affecting each other. All inputs have their own
EDID circuit.
INFO: ξ The user is not required to disconnect the video cable to change an EDID as opposed to other
ξξ
ξξξξ
ξξξξξξξξξξξξξξξξξξξξ©ξ¨ξξ¨ξξξ
ξξξξξξξξ
ξξξξξξξξξξξξξξ
ξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξ
ξξξξξξξξξξξ
ON.
INFO: ξ ξ»ξξξξξ©ξ¨ξξ¨ξξξ
ξξξξξξξξξξ
ξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξ¬ξ³ξΈξ΄ξ°ξΉξ«ξξξξξξ
ξξξξξξξξξξξξξξξξξξ·ξξξξξξξξξξξξ
do not sense this signal. In such cases, the source device must be restarted or powered OFF and ON
again.