11. Appendix MX-FR Series Modular Matrix Frames – User's Manual 141
▪ Changing audio mode on a port could have an effect on the
adjacent port's audio mode. Affected cards: MX-HDMI-3D-IB,
MX-HDMI-3D-OB, MX-TPS-IB, MX-TPS-OB.
▪
ports did not detect it correctly in some cases, and still reported
embedded audio. Affected cards: MX-HDMI-3D-IB, MX-HDMI-3D-
OB, MX-TPS-IB, MX-TPS-OB
▪ Factory default test pattern changed from solid black to color
bar. Affected cards: MX-HDMI-3D-IB, MX-HDMI-3D-OB, MX-TPS-
IB, MX-TPS-OB
▪
HDMI-3D-IB, MX-HDMI-3D-OB, MX-TPS-IB, MX-TPS-OB
▪
signal, low resolution signals (below 41 MHz TMDS clock) was
not detected by the port after unmute. Fixed. Affected cards:
MX-HDMI-OB, MX-DVI-HDCP-OB, MX-HDMI-TP-OB, MX-CPU2
(Preview output).
▪
Fixed on MX-HDMI-3D-IB-S, MX-HDMI-3D-OB-S, MX-HDMI-OB,
MX-TPS-IB-S, MX-TPS-OB-S.
▪
sample packet in the stream (but ACR packets were still present),
the MX-HDMI-OB, MX-DVI-HDCP-OB and preview output have
sent a 53Khz invalid SPDIF signal. This caused a clicking noise
with some AV receiver.
▪
changed Audio mode to Embed from aux audio). Affected cards:
MX-HDMI-3D-IB, MX-HDMI-3D-OB, MX-TPS-IB, MX-TPS-OB
3.3.8
Released: 2013-10-01
▪
that is smaller than 80x80. These commands are only valid for
the 80x80 frame.
▪ If input signal was present on a SII9575 port and test pattern
mode was changed from "Off" to "No signal mode", SII9575
output had been turned off for a short period unnecessarily.
Fixed. Affected cards: MX-HDMI-3D-IB, MX-HDMI-3D-OB, MX-
TPS-IB, MX-TPS-OB.
▪
more quickly after input signal is changed. Affected cards: MX-
HDMI-OB, MX-TPS-OB-S, MX-TPS-OB-A, MX-HDMI-3D-OB-S, MX-
HDMI-3D-OB-A.
▪ Firmware v3.3.7 sometimes rebooted with 2 or 4 line LCD display.
▪ The cycle testpattern has stopped sometimes for a few minutes.
▪ If an error happened during the booting process, there was no
alert displayed on the LCD screen (however the event has been
logged).
▪ If the errorlog menu was active on the 4-line LCD screen, then
a new incoming alert may confuse the lines on the LCD screen.
▪ Lightware simple protocol mode (P_3) could hang if an unknown
command had been received.
▪
software, every incoming charachter was capitalized. This lead
TPS) commands.
▪ Error log downloading over USB was bugous.
3.3.9
Released: 2013-10-22
▪ Display Range Limits Descriptor was not correct in factory EDIDs
(except universal EDIDs).
3.4.0
Released: 2014-01-13
New feature
▪ MX-HDMI-OPT-OB-R support has been added.
▪ New factory EDIDs have been added: 3D compliant, 4K, 4K
universal EDIDs and most often used pc graphics resolutions
with audio support.
▪
bugous data on the TPS boards.
▪ If one or more MX-TPS-IB or MX-TPS-OB (including audio addon
"PCA9673" error appeared on the LCD screen.
▪
TPS-OB, the output ports could measure strange resolution or
could not detect the incoming signal, if the DVII input changed
from no sync screen to incoming signal. Fixed.
▪ Green sparks could appear in the output signal of MX-HDMI-3D-
OB, if the input signal was coming from MX-HDMI-3D-IB and was
switched between 1080p and 480p by the crosspoint.
3.4.1
Released: 2014-03-31
▪ Some monitors that do not terminate the TMDS lines in standby
mode, could not wake up from this state, when input signal was
connected through MX-HDMI-3D-OB or MX-TPS-OB. This issue is
termination is present, but also after a hotplug event. Affected
cards: MX-HDMI-3D-OB, MX-TPS-OB.
▪ 4line LCD - View EDID menu froze the LCD task if there were no
IO cards in the matrix.
▪ 4line LCD - FR80 - View EDID did not show the 81st input and
output.
▪ 4line LCD - View EDID - Dynamic EDIDs was not displayed if there
were no input cards in the same numbered slot (the problem was
checking the input cards instead of the output cards)
▪ Too long lines in the error log may have disrupted the log reading
if special charachters were used.
▪ The text of the test pattern generator clock menu on the LCD
screen was disambigous.
▪
▪
in the card information menu.
3.4.2
Released: 2014-05-26
New feature
▪
3.4.3
Released: 2014-06-27
▪ A rare ADM1063 false alarm has appeared on the LCD or
sometimes the internal voltages were reported improperly.
Affected frame: MX-FR80
3.4.4
Released: 2014-10-08
New feature
▪ UMX-TPS devices handle the command channel even in disabled
receive mode, serial packets are discarded.
▪
To Next Page
Loading...
