212
Appendix
Appendix
SENS (Enhancer sensitivity)
Enhancer sensitivity
Value: 0–100
FREQ (Frequency)
Frequency above which is handled as the high-frequency
region
Value: 200 Hz–20.0 kHz
MIX (Enhancer mix)
Enhancer mix level
Value: 0.0–12.0 dB
THRE (De-esser threshold)
Threshold level for the de-esser
Value: -36.0–0.0 dB
EQ A/B
EQ SW (EQ switch)
Turns the EQ on/off
Value: OFF, ON
EQ ATT (EQ attenuator)
Attenuator for the EQ
Value: -42.0–+6.0 dB
TYPE (LO, LO-MID, HI-MID, HI)
Filter type. (*1)
Value: PEAK, LSV, HSV, LPF1, HPF1, LPF2, HPF2,
BPF, NOTCH, THRU
GAIN (LO, LO-MID, HI-MID, HI)
Gain. (*1)
Value: -15.0–+15.0 dB
FREQ (LO, LO-MID, HI-MID, HI)
Frequency. (*1)
Value: 20 Hz–20.00 kHz
Q (LO, LO-MID, HI-MID, HI)
Steepness of the frequency response curve. (*1)
Value: 0.36–16.00
(*1) Depending on the Type setting of each band, there are
certain combinations for which the Freq, Gain, and Q values
will have no effect, as listed below.
PEAK (Peaking)
Creates a hill or valley in the region of FREQ.
Freq: Valid Gain: Valid Q: Valid
LSV (Low Shelving)
Boosts/cuts the region below FREQ
Freq: Valid Gain: Valid Q: —
HSV (High Shelving)
Boosts/cuts the region above FREQ
Freq: Valid Gain: Valid Q: —
LPF1 (Low-Pass Filter 1)
Passes the frequency region below FREQ
Freq: Valid Gain: — Q: —
HPF1 (High-Pass Filter 1)
Passes the frequency region above FREQ
Freq: Valid Gain: — Q: —
LPF2 (Low-Pass Filter 2)
A sharper response curve than LPF1
Freq: Valid Gain: — Q: Valid
HPF2 (High-Pass Filter 2)
A sharper response curve than HPF1
Freq: Valid Gain: — Q: Valid
BPF (Band Pass Filter)
Passes the frequency region around FREQ.
Freq: Valid Gain: — Q: Valid
Notch (Notch Filter)
Removes the frequency region around FREQ
Freq: Valid Gain: — Q: Valid
THRU (Thru)
Passes all frequency regions
Freq: — Gain: — Q: —
Delay A/B
DELAY UNIT
Specifies the units for delay
Value: msec, Note, Meter, Feet,
Frame (24, 25, 29.97, 30)
DELAY SW (Delay switch)
Turns the delay on/off
Value: OFF, ON
TIME
Time between the original sound and when the delay is heard
Value: 0.0–1350 ms
FB (Feedback)
Amount of delayed sound returned to the input of the delay.
The feedback level specifies the amount of sound that is
returned. Increasing this setting will increase the number of
delay repetitions.
Value: 0–100
LO FREQ DAMP GAIN
Low-frequency attenuation of the delay sound
Value: -36.0–0.0 dB
LO FREQ DAMP FREQ
Frequency at which the low-frequency region of the delay
sound begins to be attenuated
Value: 20 Hz–2.00 kHz
M-480_e.book 212 ページ ２０１１年３月２日 水曜日 午前９時２０分
To Next Page
Loading...
