72 Programming SATEL
Reporting – ETHM/INT-GSM [Mon.ETHM-1] – the option is available if the INT-GSM /
INT-GSM LTE module is installed in the alarm system. If this option is enabled, the control
panel can send event codes via Ethernet by using the ETHM-1 Plus / ETHM-1 module
and/or via the cellular network (cellular data / SMS) by using the INT-GSM / INT-GSM LTE
module.
SMS reporting [Mon. SMS] – with this option enabled, the control panel can send event
codes to the monitoring station in the form of SMS messages. only INTEGRA 128-WRL
The SMS REPORTING option does not apply to SMS reporting by the INT-GSM /
INT-GSM LTE module.
Telephone messaging [Messaging] – if this option is enabled, the control panel can send
notifications via the telephone network of the occurrence of specific events using voice or
text messages defined by the installer.
Answering - modem [Modem answer.] – with this option enabled, external initiation of the
communication between modem and control panel is possible.
Answering - audio [Voice answer.] – with this option enabled, the control panel will carry out
the function of call answering.
The ANSWERING - AUDIO option must be enabled, if the users are to operate the alarm
system using the interactive voice menu offered by the INT-VG module.
Remote control – with this option enabled, the control panel allows the users having
a telephone code to operate the REMOTE SWITCH outputs by using a phone. The option is
available if the ANSWERING – AUDIO is enabled.
External modem [External modem] – with this option enabled, the control panel will support
an external modem connected to the control panel RS-232 port.
Modem ISDN/GSM/ETHM [ISDN/GSM modem] – enable this option if the ETHM-1 Plus /
ETHM-1 / INT-GSM / INT-GSM LTE / GSM / ISDN module is connected to the control
panel RS-232 port. The option is available if the EXTERNAL MODEM option has been
enabled.
Answering - ETHM/GSM [Ext.mod.answ.] – if this option is enabled, it is possible to
establish connection with the alarm control panel via the ETHM-1 / ETHM-1 Plus module,
INT-GSM / INT-GSM LTE module, GSM or ISDN modem. The option is available, if the
EXTERNAL MODEM and MODEM ISDN/GSM/ETHM options are enabled. The option is not
available when the ANSWERING - MODEM option is enabled, which also enables to establish
connection with the alarm control panel via the ETHM-1 / ETHM-1 Plus module, INT-GSM
/ INT-GSM LTE module, GSM or ISDN modem.
Tone dialing – with this option enabled, the control panel will tone dial the telephone
numbers (pulse dial, if this option is disabled).
Ground Start – with this option enabled, the control panel will use the Ground Start method
to obtain signal on the telephone line (by grounding temporarily the telephone line wires).
Enable this option, if required by your phone service provider.
No dial tone test [No dialton.tst] – with this option enabled, the control panel will not perform
the test for dial tone before dialing the number and will start dialing the number 5 seconds
after going “off hook”. This makes it possible for the control panel to dial the number when
some non-standard tones occur after going off hook (e.g. interrupted tone). When this
option is disabled, the control panel will start dialing the number 3 seconds after going off
hook, provided that the dial tone is present.
No answer test – with this option enabled, in case of notifying by means of voice
messages, the control panel will not perform the test for “off hook” condition. The
voice message will be played back 15 seconds after completion of the number dialing.
Double voice message [Dbl. voice msg.] – with this option enabled, the voice message is
played back twice during telephone messaging.
To Next Page
Loading...
