MX-2300/2700 N/G SIMULATION 7 – 42
3) When [OK] button is pressed, and the current set value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.
* When [CA] key or [SYSTEM SETTINGS] key is pressed to
exit the simulation, the machine is rebooted.
<Setting range and default value of each set value>
*: The FSS connection test can be changed only from Disable to
Enable, and cannot be changed from Enable to Disable.
30
30-1
Purpose : Operation test/Check
Function (Purpose) : Used to check the operations of the sen-
sors and detectors in the paper feed sec-
tion, the paper transport section, and the
paper exit section.
Section : Paper feed
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 30-01, the following
screen is displayed to show the sensor status change.
* When each sensor is turned ON, the corresponding sensor
name is highlighted.
<Sensor name>
30-2
Purpose : Operation test/Check
Function (Purpose) : Used to check the operations of the sen-
sors and detectors of the paper feed sec-
tion and the related circuits.
Section : Paper feed
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 30-02, the following
screen is displayed to show the sensor status change.
* When each sensor is turned ON, the corresponding sensor
name is highlighted.
<Sensor name>
Item Display Content
Setting
range
Default
A CONNECTION
TEST MODE
(1: ON 0: OFF)
1 Set the FSS connection
test mode to Enable.
0 to 1 0
(OFF)
0 Set the FSS connection
test mode to Disable. *
Code of sensor Sensor name
PPD1 Resist front detection
PPD2 Resist detection
POD1 Fusing after detection
POD2 Paper exit detection
POD3 Right tray paper exit detection
TFD2 Main unit paper exit full detection
TFD3 Right tray paper exit full detection
HPOS Shifter home detection
DSW_R Right door open/close detection
DSW_C Cassette 1 transport cover open/close detection
DSW_F Front cover open/close detection
DHPD_K K phase detection
DHPD_CL CL phase detection
1TNFD Waste toner full detection
1TUD_CL Primary transfer belt separation CL detection
1TUD_K Primary belt separation BK detection
0
A:
A:0
; CONNECTION TEST MODE (1:ON 0:OFF)
SIMULATION NO.27-14
FSS TEST MODE SETUP
0
[0~ 1]
OK
TEST
CLOSE
Sensor name (Display) Content
CPFD1 Cassette 1 transport detection
CLUD1 Cassette 1 upper limit detection
CPED1 Cassette 1 paper empty detection
CSPD1 Cassette 1 paper remaining quantity detection
CSS1 Cassette 1 presence detection
CPFD2 Cassette 2 transport detection
CLUD2 Cassette 2 upper limit detection
CPED2 Cassette 2 paper empty detection
CSPD2 Cassette 2 paper remaining quantity detection
CSS2 Cassette 2 presence detection
MPFD Manual feed paper entry detection
MPLD Manual feed paper length detection
MTOP1 Manual feed tray reduction detection
MTOP2 Manual feed tray extension detection
MPED Manual feed paper empty detection
0
MAIN UNIT SENSOR CHECK
CLOSE
SIMULATION NO.30-01
TEST
1/1
PPD1 PPD2 POD1 POD2
POD3 TFD2 TFD3 HPOS
DSW_R DSW_C DSW_F DHPD_K
DHPD_CL 1TNFD 1TUD_CL 1TUD_K
0
TRAY SENSOR CHECK(MAIN)
1/1
CLOSE
SIMULATION
NO.30
㧙
02
TEST
1/1
CPFD1 CLUD1
CPED 1
CSPD 1
CSS1 CPFD2
CLUD 2
CPED 2
CSPD 2
CSS2 MPFD MPLD
MTOP1
MTOP2 MPED
To Next Page
Loading...
