MX-2300/2700 N/G OTHERS 12 – 3
◆ Customize 3 Quick File
X USB Memory Scan
◆ Customize 1 Special Modes
◆ Customize 2 Erase
◆ Customize 3 Suppress BG
X Data Entry
◆ Customize 1 Special Modes
◆ Customize 2 File
◆ Customize 3 Quick File
■ Device Control
● Original Size Detector Setting
X Original Detection Size
Combination
Varies depending on
country and region
X Cancel Detection at Document
Glass
Disable
● Disabling of Document Feeder*3 Disable
● Original Feeding Mode*3 All Disabled
● Disabling of Duplex Disable
● Disabling of Large Capacity Cassette*7 Disable
● Disabling of Optional Paper Drawer*8 Disable
● Disabling of Tray Setting Disable
● Disabling of Finisher*9 Disable
● Disabling of Offset Disable
● Disabling of Stapler*9 Disable
● Saddle Stitch Position Adjust*10 0.0 mm
● Disabling of Punch*11 Disable
● Disabling of Colour Mode*12 Disable
● Auto Paper Selection Setting Plain Paper
● Registration Adjustment
X Auto Adjustment -
● Optimization of the Hard Disk -
● Tandem Connection Setting
X IP Address of Slave Machine 0.0.0.0
X Port Number 50001
X Disabling of Master Machine Mode Disable
X Disabling of Slave Machine Mode Disable
● Clear All Job Log Data -
● Detect Standard in Auto Colour Mode 3
■ Copy Settings
● Initial Status Settings
X Colour Mode Full Colour
X Paper Tray Varies depending on the
machine configuration
X Exposure Type Auto
X Copy Ratio 1
X 2-Sided Copy 1-Side to 1-Side
X Output -
● Exposure Adjustment
X Colour
◆ Document Glass 5
◆ Document Feeder 5
X B/W
◆ Document Glass 5
◆ Document Feeder 5
● Rotation Copy Setting Enable
● Add or Change Extra Preset Ratios
X Reduction -
X Enlargement -
● Setting a Maximum Number of Copies 999
● Initial Margin Shift Setting
X Side-1 10 mm (1/2")
X Side-2
● Erase Width Adjustment
X Edge 10 mm (1/2")
X Centre
● Card Shot Settings
X Original Size X: 86 mm (3-3/8") Y: 54
mm (2-1/8")
X Fit to Page Disable
● Automatic Saddle Stitch*10 Enable
● Initial Tab Copy Setting 10 mm (1/2")
Item Factory default setting
● Disabling Deletion of Job Programs Disable
● Disabling of Bypass-Tray in Duplex
Copy
Disable
● Disabling of Auto Paper Selection Disable
● Auto Selection Setting of Tray that is
Supplied the Paper
Disable
● Initial Colour Balance Setting Factory Default State
● Auto Colour Calibration -
● B/W 600dpi x 600dpi Scanning Mode
for Document Feeder*3
Disable
● B/W Quick Scan from Document Glass Enable
■ Network Settings
● IP Address Setting DHCP
● Enable TCP/IP Enable
● Enable NetWare Enable
● Enable EtherTalk Enable
● Enable NetBEUI Enable
● Reset the NIC -
● Ping Command -
■ Printer Settings
● Default Settings
X Prohibit Notice Page Printing Enable
X Prohibit Test Page Printing Disable
X A4/Letter Size Auto Change Varies depending on
country and region.
X Print Density Level
◆ Colour 3
◆ B/W 3
X Bypass Tray Settings
◆ Enable Detected Paper Size in
Bypass Tray
Disable
◆ Enable Selected Paper Type in
Bypass Tray
Enable
◆ Exclude Bypass-Tray from Auto
Paper Select
Disable
X Job Spool Queuing Enable
● Interface Settings
X Hexadecimal Dump Mode*1 Disable
X I/O Timeout 20 sec.
X Enable USB Port Enable
X USB Port Emulation Switching*1 PCL (Auto*13)
X Enable Network Port Enable
X Network Port Emulation
Switching*1
PCL (Auto*13)
X Port Switching Method Switch at End of Job
● Colour Adjustments
X Auto Colour Calibration -
■ Image Send Settings*14
● Operation Settings
X Default Display Setting
◆ Mode Scanner*4 (Fax*6)
◆ Hold settings for a while after
scanning has been completed
Disable
◆ Switch Automatically to Copy
Mode Screen
Disable
X Initial Resolution Setting
◆ Apply the Resolution Set when
Stored
Disable
◆ Scanner*4 200x200dpi
◆ Internet Fax*5 200x100dpi
◆ Fax*6 Standard
X Default Exposure Settings
◆ Exposure Auto
◆ Original Image Type Text
◆ Moiré Reduction Disable
X Must Input Next Address Key at
Broadcast Setting
Disable
X Scan Complete Sound Setting Middle
X The Number of File Name/Subject/
Body Keys Displayed Setting
6
X The Number of Direct Address
Keys Displayed Setting
6
Item Factory default setting
To Next Page
Loading...
