Siemens SITRANS F - Page 35

1010ENFM-3BTable Of Contents
v
Using the “F4” Reset Sequence............................................................ 2-83
Troubleshooting With Transducer Test Blocks ........................................ 2-85
2.11.10 Using The 1012TB-1 And 2 Test Blocks ...................................................... 2-85
2.11.11 Using The 996PSP Pipe Simulator ............................................................. 2-87
If a Pipe Simulator/Test - Block Test Fails ............................................... 2-88
2.12 Guide To A Smooth Installation ................................................................. 2-89
2.12.1 Checklist For 1010 Start-Up & Performance .............................................. 2-89
2.12.2 Optimization/Correction Of Problems ....................................................... 2-90
“Official” Coupling Compounds ............................................................ 2-92
“Alternative” Coupling compounds ....................................................... 2-92
Ideal Vsig Display................................................................................ 2-93
Section 3
3. Hardware Installation Guide ........................................................................ 3-1
3.1 Preparing To Mount The Transducers .......................................................... 3-1
3.1.1 How To Identify 1011 Transducers and Mounting Hardware ...................... 3-1
3.1.2 Selecting A Location for Clamp-On Transducers ......................................... 3-1
3.1.3 Clamp-On Transducer Mounting Modes ..................................................... 3-2
3.1.4 Preparing The Pipe .......................................................................................3-3
3.1.5 Reflect Mode With EZ Clamp And Spacer Bar Only ..................................... 3-4
3.1.6 Direct Mode With EZ Clamp And Spacer Bar Only ........................................3-5
3.1.7 Reflect Mode-Mounting Frames and Spacer Bar ......................................... 3-9
3.1.8 Reflect Mode With Spacer Bar Only ........................................................... 3-10
3.1.9 Direct Mode-Mounting Frames, Spacer Bar & Spacing Guides .................. 3-12
3.1.10
Using 1012T Mounting Trac
ks.................................................................... 3-16
Installing a 1012T Mounting Track in Reflect Mode ................................ 3-16
Installing a 1012T Mounting Track in Direct Mode ................................. 3-18
3.2 Mounting Temperature Sensors ................................................................ 3-19
3.2.1 Wiring Temperature Sensor To The Analog Input Module ........................ 3-20
3.2.2 FUE1010EN Supply And Return Connections ............................................ 3-21
3.2.3 Notes On Clamp-on RTD Installation ......................................................... 3-21
3.2.4 Paralleling RTD Inputs For Dual-Channel Energy Measurement................ 3-22
Section 4
4. The Meter Facilities Menu and Graphic Display Screens ............................. 4-1
4.1 Preferred Units ............................................................................................ 4-1
4.2 The Table Setups Menu ............................................................................... 4-2
4.2.1 Pipe Table .................................................................................................... 4-2
Pipe Table Menu Structure ..................................................................... 4-2
4.2.2 Create/Edit Pipe ........................................................................................... 4-3
4.2.3 Delete Pipe .................................................................................................. 4-4
4.3 Transducer Type Menu ................................................................................ 4-4
Transducer Type Menu Structure ............................................................ 4-5
4.4 The Datalogger Control Menu ..................................................................... 4-6
4.4.1 Display Datalogger ...................................................................................... 4-6
4.4.2 Output Datalogger ....................................................................................... 4-7
4.4.3 Circular Memory .......................................................................................... 4-7
4.4.4 Est Log Time Left ......................................................................................... 4-8
4.4.5 Clear Datalogger .......................................................................................... 4-8
4.5 The Memory Control Menu
.......................................................................... 4-8
4.5.1 The Analog Output Trim Menu .................................................................... 4-9