PURESTRENGTH & BENCHES: Guida all'Assistenza Tecnica - rev. 4.1
Page i
Contents
1. GENERAL NOTICES ............................................................................................................................................. 1.1
1.1. INTRODUCTION ................................................................................................................................................... 1.1
1.2. RECOMMENDATIONS .......................................................................................................................................... 1.1
1.3. GENERAL RULES FOR REPAIR PROCEDURES ........................................................................................................ 1.2
2. TECHNICAL CHARACTERISTICS .................................................................................................................... 2.1
2.1. ENCODING EQUIPMENTS ..................................................................................................................................... 2.1
2.2. ENCODING BENCHES .......................................................................................................................................... 2.2
2.3. AMBIENT SPECIFICATIONS .................................................................................................................................. 2.3
2.4. CONFORMITY TO REGULATIONS .......................................................................................................................... 2.3
2.5. MECHANICAL CHARACTERISTICS......................................................................................................................... 2.3
2.5.1. minimum load to the lever without weights (user's hand) ...................................................................... 2.3
2.6. MECHANICAL CHARACTERISTICS ....................................................................................................................... 2.4
2.6.1. Equipment Characteristics ..................................................................................................................... 2.4
2.6.2. Benches Characteristics ....................................................................................................................... 2.19
3. INSTALLING AND MOVING THE EQUIPMENT ............................................................................................ 3.1
3.1. INSTALLATION SPECIFICATIONS AND REQUIREMENTS ......................................................................................... 3.1
3.2. INSTALLING THE EQUIPMENT TO BE ASSEMBLED ................................................................................................. 3.1
3.3. EQUIPMENT INSTALLATION ................................................................................................................................. 3.2
3.4. MOVING ............................................................................................................................................................. 3.2
3.5. EQUIPMENT FASTENING TO THE GROUND ............................................................................................................ 3.3
3.6. POWER RACK FASTENING TO THE GROUND (PG11) ............................................................................................ 3.4
4. ACCESSORIES........................................................................................................................................................ 4.1
4.1. A0000356-XX: PLATE RACK ............................................................................................................................. 4.1
4.2. A0000374: PLATE HOLDER KIT WITH 2 PINS ....................................................................................................... 4.2
4.3. A0000363: PLATE RACK KIT WITH 1 PIN ............................................................................................................ 4.3
4.4. A0000398-XX: PLATE SUPPORT ACCESSORY ..................................................................................................... 4.4
4.5. A0000447-XX: CONNECT ADJUSTABLE RACK .................................................................................................. 4.5
4.6. A0000520-XX: BARBELL HOLDER RACK (10 SEATS) .......................................................................................... 4.6
4.7. A0000521-XX: HANDLEBAR HOLDER RACK (10 PAIRS) ...................................................................................... 4.7
4.7.1. ACCESSORIES - PG11 .......................................................................................................................... 4.8
5. DISASSEMBLING COMPONENTS ..................................................................................................................... 5.1
5.1. DISASSEMBLING COMMON TO SEVERAL EQUIPMENT ........................................................................................... 5.1
5.1.1. Seat adjustment system ........................................................................................................................... 5.1
5.1.2. Disassembling the handles ..................................................................................................................... 5.3
5.1.3. Disassembling the handles ..................................................................................................................... 5.4
5.1.4. Upholstery .............................................................................................................................................. 5.5
5.1.5. Disassembling the lever limit buffers ..................................................................................................... 5.5
5.1.6. Disassembling the easy-start lever spring .............................................................................................. 5.6
5.1.7. Disassembling the levers ........................................................................................................................ 5.7
5.1.8. Disassembling the plate rack pins .......................................................................................................... 5.9
5.1.9. Disassembling the stretching handle .................................................................................................... 5.10
5.1.10. Disassembling the adjusting foot ......................................................................................................... 5.11
5.2. DISASSEMBLING THE CALF (MG45) ................................................................................................................. 5.12
5.2.1. Calf Guard ........................................................................................................................................... 5.12
5.2.2. Calf padding ......................................................................................................................................... 5.13
5.2.3. Calf carriage ........................................................................................................................................ 5.14
5.2.4. Disassembling the calf carriage wheels and rollers ............................................................................. 5.16
5.2.5. Disassembling the Calf limit buffers .................................................................................................... 5.18
To Next Page
Loading...
