FR
3. Faire passer le l par le guidage
(1) en introduisant le l du côté
droite.
4. Ensuite faire passer le l vers
le bas et le faire passer par
les disques du tendeur du l
supérieur (2).
5. Remontez le l vers le haut
au-dessus des disques (2) en le
tendant fort an que le ressort
du tendeur ne saute pas.
6. Faire passer le l du côté droit
vers le côté gauche par l’oeillet du
releveur du l (3).
7. Faire ensuite passer le l vers le bas
dans la direction de l’aiguille et enler
par le guidage inférieur du l (4) et par
le guidage suivant à la hauteur du l
(5).
8. Enlez l’oeillet de l’aiguille en faisant
passer le l par devant vers l’arrière
(6) et faire passer en-dessous du pied
presseur pour une longueur d’environ
10 cm.
1. Pendant l’enlage de
l’aiguille gauche procéder
identiquement comme dans
le cas de l’enlage d’une
aiguille (passer le l par les
points désignés sur l’image de
1 à 5).
2. Ensuite passez le l par la
partie extérieure des guidages
(5) comme le montre l’image.
3. Passez le l par l’aiguille de
l’arrière vers l’avant.
4. Enlez l’aiguille droite après
l’enlage de l’aiguille gauche.
Procéder de la manière
standard.
5. Passez le l par l’aiguille de l’avant vers l’arrière.
7
KNOWING YOUR SEWING MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread sp
ool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading the machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do n
ot block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
7
KNOWING YOUR SEWING MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread sp
ool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading the machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do n
ot block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
DOUBLE AIGUILLE
7
KNOWING YOUR SEWING MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread sp
ool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading the machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do n
ot block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
Fil de l’aiguille
gauche
Fil de l’aiguille
droite
Texi Fox 25126