Texi Fox 25 User Manual

ZAČÁTEK A KONEC ŠVU
ŠITÍ ROHŮ
Upozornění: Při šití je třeba věnovat zvýšenou
pozornost okolí jehly.
Stroj podává látku sám, není tedy třeba ji při šití
postrkovat ani tahat.
1. Jehlu zdvihněte do nejvyšší polohy pomocí
tlačítka pro nastavení pozice jehly.
2. Umístěte látku podp řítlačnou patku.
3. Spusťte přítlačnou patku.
4. Přidržujte obě nitě vzadu při zahájení šití. Po ušití
několika stehů je můžete uvolnit.
5. Při šití ovládejte rychlost pomocí pedálu.
6. Jakmile dosáhnete konce švu, zastavte stroj.
7. Zdvihněte přítlačnou patku.
8. Jakmile dosáhnete konce švu, zastavte stroj a
otočte ručním kolem k sobě pro zdvih jehly do
nejvyšší polohy. Vytáhněte látku ze stroje, pro
odříznutí nití použijte zabudovaný ořez - na boční
straně čelního krytu
Zastavte stroj, jakmile dosáhnete rohu.
Spusťte jehlu do látky. Zdvihněte
přítlačnou patku. Otočte látkou kolem
jehly do požadovaného směru. Spusťte
přítlačnou patku a pokračujte v šití .
13
UTILITY STITCHES
Straight stitch
Raise the presser foot and position the fabric next to a
stitching guide line on the needle plate.
Lower the needle into the fabric.
Lower the presser foot and smooth the thread towards the
back. Depress the foot control.
Gently guide the fabric along the guide line letting the
fabric feed by itself.
For fastening the ends of seams, press the reverse stitch
button and sew several reverse stitches.
Raise the presser foot and remove the fabric, drawing the
threads to back.
The threads are cut the proper length for starting the next
seam.
A
B
2~6
1.5~4
Machine Setting
12
KNOWING YOUR SEWING MACHINE
Useful sewing tips
Various ways to achieve better sewing results are described below.
Refer to these tips when sewing.
1. Trial sewing
Use different stitch width and length for trial sewing. When you have finished, select the
best looking stitch width and length for correct sewing.
For the trial sewing, use a piece of fabric and thread that are the same as those used for
your project, and check the thread tension and stitch length and width. Since the results
differ depending on the type of stitching and the number of fabric layers sewn, perform the
trial sewing under the same conditions th
at will be used with your project.
3. Sewing curves
1).Stop sewing, and then slightly change the sewing direction to sew around the curve.
2).When sewing along a curve while using a zigzag stitch, select a shorter length in order to
obtain a finer stitch.
4. Sewing thick fabrics
If the fabric does not fit under the presser foot
Raise the presser foot even higher to bring the presser foot to its highest position. Then feed
the fabric under the presser foot. (See page 4 to Raise the presser foot.)
5. Sewing elastic fabric or the fabric that is easy to cause skipping stitches
Use round head needle and b
igger stitch length. If necessary, add one layer of lining cloth
under the fabric for better sewing.
6. Sewing thin fabric or silk
When sewing thin fabric or silk, the stitch may depart from correct direction or cannot feed the
fabric correctly. If so, add one layer of lining cloth under the fabric for better sewing.
7. Sewing stretch fabrics
First, baste the piece of fabric together, and then sew without stretching the fabric.
8. Free arm sewing
When sewing tube fabric or the part cannot reach, use the free arm sewing function (For
detail, refer to page 4).
2. Changing the sewing direction
Stop the machine and turn the hand wheel
toward you to bring the needle down into the
fabric. Raise the presser foot.
Pivot the fabric around the needle to change
sewing direction as desired. Lower the
presser foot and continue sewing.
Texi Fox 25 19
CS

Texi Fox 25 Specifications

General

Brand	Texi
Model	Fox 25
Category	Sewing Machine
Language	English