Texi Fox 25 User Manual

PL
3. Przeprowadź nitkę przez
prowadnik (1) wprowadzając
nitkę od prawej strony.
4. Dalej prowadź nitkę w dół
iprzeprowadź przez talerzyki
naprężacza nici górnej (2)
ipoprowadź w górę.
5. Przełóż nitkę od prawej
strony do lewej przez oczko
podciągacza nici (3).
6. Następnie prowadź nitkę w
dół w kierunku igły iprzewlecz
przez dolny prowadnik nici (4&5) oraz
przez kolejny prowadnik nawysokości
igły (6).
7. Nawlecz oczko igły przeciągając nić
od przodu do tyłu (7) i przeciągnij pod
stopką na długość ok. 10 cm.
1. Podczas nawlekania lewej
igły postępuj analogicznie
jak w przypadku nawlekania
jednej igły (przewlecz nitkę
przez punkty zaznaczone na
rysunku od 1 do 5).
2. Następnie przeprowadź
nitkę wewnątrz sprężynki
znajdującej się w prowadniku
(5) jak pokazano na rysunku .
3. Przewlecz nitkę przez igłę od
tyłu do przodu.
4. Po nawleczeniu lewej igły,
nawlecz igłę prawą. Postępuj
w standardowy sposób.
5. Przewlecz nitkę prawą przez
igłę od przodu do tyłu.
7
KNOWING YOUR SEWING MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread sp
ool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading the machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do n
ot block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
7
KNOWING YOUR SEWING MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread sp
ool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading the machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do n
ot block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
PODWÓJNA IGŁA
7
KNOWING YOUR SEWING MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread sp
ool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading the machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do n
ot block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
Nić lewej igły
Nić prawej igły
Texi Fox 25154

Texi Fox 25 Specifications

General

Brand	Texi
Model	Fox 25
Category	Sewing Machine
Language	English