Texi Fox 25 User Manual

ES
3. Pase el hilo por el guía hilos
(1), pasando el hilo desde la
derecha.
4. A continuación, dirija el hilo
hacia abajo y páselo por
los discos tensores del hilo
superior (2).
5. Estire el hilo hacia arriba
por encima de los discos (2)
tensándolo rmemente hasta
que salte el muelle del tensor.
6. Pase el hilo del lado derecho al
izquierdo a través del ojo de recogida
del hilo (3).
7. A continuación, dirija el hilo hacia
abajo en dirección a la aguja y páselo
por el guía hilos inferior (4) y por la
siguiente guía situada a la altura de la
aguja (5).
8. Enhebre el ojo de la aguja estirando
del hilo de delante hacia atrás (6) y
páselo por debajo del prensatelas
unos 10 cm aprox.
1. Durante el enhebrado de
la aguja izquierda, proceda
del mismo modo que el
enhebrado de una aguja
(ensarte el hilo por los puntos
indicados en las guras 1 a 5).
2. Posteriormente dirige el hilo
por el lado exterior de la guía
(5) como se muestra en la
gura.
3. Enhebre la aguja de atrás
hacia adelante.
4. Después de enhebrar la aguja
izquierda, enhebre la aguja
derecha. Proceda de forma
estándar.
5. Enhebre el hilo derecho en la aguja de adelante hacia atrás.
7
KNOWING YOUR SEWING MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread sp
ool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading the machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do n
ot block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
7
KNOWING YOUR SEWING MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread sp
ool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading the machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do n
ot block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
AGUJA DOBLE
7
KNOWING YOUR SEWING MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread sp
ool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading the machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do n
ot block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
Hilo de la aguja
izquierda
Hilo de la aguja
derecha
Texi Fox 2598

Texi Fox 25 Specifications

General

Brand	Texi
Model	Fox 25
Category	Sewing Machine
Language	English