What to do if Tuttnauer 5050 Laboratory Equipment safety valve does not release pressure?
If the safety valve on your Tuttnauer Laboratory Equipment does not release pressure during a blow-off test: * If circulation is blocked, remove the obstruction. * If the issue persists, replace the faulty valve.
What to do if my Tuttnauer 5050 says 'Door is open (During the cycle)'?
If your Tuttnauer Laboratory Equipment displays a 'Door is open (During the cycle)' message, it means the door is open during the cycle. Close the door to perform a new cycle.
What does 'Time Error' mean on my Tuttnauer Laboratory Equipment and how do I resolve it?
If your Tuttnauer Laboratory Equipment displays a 'Time Error' message, it means the real-time clock is faulty and the main board needs to be replaced.
What to do if the chamber temperature is not in range in Tuttnauer 5050?
If the chamber temperature of your Tuttnauer Laboratory Equipment is not within the expected range, wait until the chamber reaches the normal range temperature.
What does 'Compressed air supply error (C - cooling) only' mean on my Tuttnauer 5050 and how do I fix it?
If your Tuttnauer Laboratory Equipment displays a 'Compressed air supply error (C - cooling) only' message, it indicates a malfunction in the compressed air supply. This can be due to the compressed air valve not opening because of a faulty connection or a faulty I.O. board, or the compressed air valve itself might be faulty. Check and fix the compressed air supply. If the problem persists, fix the connection, replace the faulty I.O. board, or replace the faulty valve.
What does 'High Pressure (Exhaust)' indicate on my Tuttnauer Steriliser?
If the Tuttnauer Steriliser displays 'High Pressure (Exhaust)', it means the system cannot reach preset pressure within 10 minutes from the beginning of the exhaust stage. You should perform a new cycle.
What to do if the 'Door is open' during the cycle on Tuttnauer Laboratory Equipment?
If your Tuttnauer Laboratory Equipment indicates that the 'Door is open' during the cycle, close the door to perform a new cycle.
Why Tuttnauer Laboratory Equipment printer feeds paper continuously?
If the printer feeds paper continuously when the Tuttnauer Laboratory Equipment is switched on, make sure the ‘feed button’ on the printer is not stuck.
What to do if Tuttnauer Laboratory Equipment shows low temperature I N I M?
If your Tuttnauer Laboratory Equipment displays a low temperature (I N I M) error, try the following: * Perform a new cycle, ensuring you do not overload the chamber. * Replace the door gasket. * Recalibrate the temperature and pressure sensors. * Check and fix any loose connections. * If the problem continues, replace any faulty temperature or pressure sensors, the SSR, or the Analog board.
What does 'High Pressure (Exhaust)' mean on my Tuttnauer 5050 Laboratory Equipment and how do I fix it?
If your Tuttnauer Laboratory Equipment displays a 'High Pressure (Exhaust)' message, it means the system couldn't reach the preset pressure within 10 minutes from the beginning of the exhaust stage. This can be due to the exhaust valve not opening because of a faulty connection or a faulty I.O. board, or the exhaust valve itself might be faulty. First, perform a new cycle. If the problem persists, fix the connection, replace the faulty I.O. board, or replace the faulty valve.
Overview of the laboratory sterilizer, its models, and features.
Procedures for unpacking and inspecting the autoclave upon receipt.
Details of the product warranty, coverage, and exclusions.
Information on warranty registration and technical service contact.
Lists relevant directives and standards the autoclave complies with.
Details water quality requirements and system utilities.
Covers electrical configurations, operating conditions, and performance.
Includes construction materials, emissions, and dimensions.
Provides detailed model specifications and sticker descriptions.
Diagrams showing the front and rear views of the autoclave.
Diagram of the control panel and its numbered components.
Explains the functions of the UP, DOWN, and START/STOP keys.
Lists and explains operational and error messages and symbols.
Describes the optional printer and its role in the system.
Details the Glass sterilization program parameters and sequence.
Details the Plastic sterilization program parameters and sequence.
Details the Liquid A sterilization program, cautions, and sequence.
Details the Liquid B – Waste sterilization program, cautions, and sequence.
Details the Liquid A – Cooling program parameters and sequence.
Details the Liquid B – Waste Cooling program parameters and sequence.
Details the Bio Hazard 1 program for bio-hazard models.
Details the Bio Hazard 2 program for bio-hazard models.
Details the Bio Hazard Liquids program for bio-hazard models.
Details the Vacuum Test program for PV models.
Details the Warm-Up program for pre-warming the chamber.
Details the Isothermal program for liquids, agar, pasteurization.
Details the Air Mixture program for liquids in soft packages.
Details the Glass Test program for checking bottle durability.
Details the Durham program for liquids.
Illustrates screens shown after a successful sterilization cycle.
Shows screens for cycles aborted after sterilization.
Illustrates screens indicating a general cycle failure.
Instructions for browsing menus and changing parameters.
Accessing quick options, setting date/time, and system parameters.
Details on managing cycle parameters like Dry Time.
Information on printer output content and paper handling.
Guidelines for treating thermal papers and powering off the printer.
Guidelines for preparing instruments, tubing, and liquids.
Instructions for filling the autoclave's water reservoir.
Steps for turning on the autoclave and opening/closing doors.
How to start, run, and unload the autoclave cycle.
Instructions for setting a future start time for the sterilization cycle.
Covers daily, weekly, periodic maintenance and tests.
Instructions for draining the reservoir and cleaning the strainer.
Guidance on checking safety valves and moving the autoclave.
Addresses issues with display, printer, sensors, and range errors.
Covers system, cycle, pressure, and time-related errors.
Addresses errors related to jacket temp, maintenance, water, vacuum, and cycle counts.
General| Brand | Tuttnauer |
|---|---|
| Model | 5050 |
| Category | Laboratory Equipment |
| Language | English |
To Next Page