YASKAWA P7 - Page 251

Index - 7
Loss Detection Time.................................5-18, A-6
Reference Missing Detection ...................5-18, A-6
Square Root Function Activation..............5-23, A-6
Integral Limit Setting.......................................5-17, A-5
Integral Time Setting........................................5-16, A-5
Maximum Boost Time .....................................5-22, A-6
Offset Adjustment........................................... 5-17, A-5
Output ......................................................................5-17
Gain Setting ..............................................5-18, A-5
Level Selection..........................................5-17, A-5
Limit..........................................................5-17, A-5
Square Root Monitor.................................5-23, A-6
Parameters...................................5-15 to 5-23, A-5, A-6
Primary Delay Time Constant...................................A-5
Setpoint ...........................................................5-15, A-6
Boost Setting.............................................5-21, A-6
Display Scaling.........................................5-20, A-6
Selection....................................................5-19, A-6
Value .........................................................5-20, A-6
Sleep
Delay Time................................................5-19, A-6
Function ............................................................5-19
Function Start Level..................................5-19, A-6
Input Source..............................................5-21, A-6
Snooze
Deactivation Level....................................5-12, A-6
Delay Time................................................5-21, A-6
Feedback Level.........................................5-22, A-6
Function ............................................................5-21
Level .........................................................5-21, A-6
Square Root Gain.............................................5-23, A-6
PI Mode...................................................................5-15, A-5
PI Monitors
Feedback (U1-24)...........................................5-20, A-27
Output (U1-37)...............................................5-19, A-27
Setpoint (U1-38).............................................5-20, A-27
PLC (Programmable Logic Controller)
Serial Com. Using Modbus Protocol ........................D-2
Troubleshooting .......................................................6-17
Power
Detection Filter Time................................................A-7
Energy Saving..........................................................5-24
Output, +15Vdc.............................................. 2-23, 2-27
Loss Ride-thru .......................................5-39, A-19, C-4
Module Spare Parts............................................F-2, F-3
PCB
Inspecting............................................................7-2
Spare Parts ..................................................F-2, F-3
Supply Specifications........................................C-2, C-3
Power Factor Correction Capacitors .................................6-6
Pre-Operation Considerations ...................i to iv; Ch. 1, 2, 4
Preset Speeds....................................................................A-8
Preventive Maintenance.................................................... 7-3
Programming
Basic ..............................................................5-1 to 5-60
Error (OPE).............................................................. 6-11
Menu..............................................................3-6 to 3-15
Proportional Gain (PI) ............................................. A-5
Protective
Functions ...................................................................C-4
Structure.....................................................................C-4
PWM Frequency — See Carrier Frequency.................... A-8
Q
Quick Setting Menu........................................................ 3-11
R
RAM .............................................................................. D-12
Ramp to Stop .................................................................... 5-6
Rated Current, Motor....................4-6, 5-31, 6-12, A-11, B-4
Rdy.................................................................................... 3-2
Reactors, Preventive Maintenance.................................... 7-3
READ..............................................................................5-56
Ready Display................................................................... 3-2
Receiving ......................................................................... 1-3
REF Indicator ............................................................3-2, 3-4
Reference Limits
(Also see Frequency) ..........5-26, 6-19, A-9
Reference Source......................................................5-4, A-4
Relays, Preventive Maintenance....................................... 7-3
REMOTE
Key............................................................................. 3-3
Mode.......................................................................... 3-3
REF Indicator .....................................................3-2, 3-4
SEQ Indicator ....................................................3-2, 3-4
Replacement Parts .................................................... F-2, F-3
Also see Spare Parts Ordering...........Inside Back Cover
RESET Key ...................................................................... 3-3
Resistance, Motor Line-to-Line .....................................A-11
Resonance....................................................................... 5-27
REV Indicator ................................................................. 3-4
Reverse Operation.....................................................5-8, A-4
Prohibiting ................................................5-8, 6-16, A-4
Reverse Run/Stop command..................................2-23, 2-27
Ride-thru, Momentary Power Loss......5-11, 5-39, A-19, C-4
"Right Arrow" Key........................................................... 3-3
RS-485/422 ...................................................................... 5-5
Communication Wiring ............................................ D-3
Control Circuit Terminals........................................2-23
Parameters ..............................................5-4, 5-32, A-18
Terminating Resistance....................................2-24, D-3