YASKAWA P7 - Page 252

Index - 8
RTS Control Selection....................................................A-18
Run Command
During Program..................................................5-8, A-4
External, Troubleshooting........................................6-15
Selection..............................................3-4, 4-6, 5-4, A-4
Source.........................................................................5-4
RUN Indicator...................................................................3-5
Running
Signal........................................................................2-23
Stall Prevention during...................................5-42, A-20
S
Scaling Display
Digital Operator .............................................5-52, A-23
PI Setpoint........................................................5-20, A-6
S-Curve Characteristic
at Accel End..............................................................A-7
at Accel Start............................................................ A-7
Search Operation Voltage Limit.......................................A-7
SEQ ...................................................................................3-4
Sequence Parameters........................................................A-4
Serial Communications ....................................................D-2
Address......................................................................D-4
Baud Rate...........................................................6-8, D-4
Drive Node Address..................................................D-4
Parameters.......................................................A-18, D-4
Run Command ...........................................................5-4
Self-Diagnosis Function..........................................D-14
Serial Number ...................................................................1-3
Setpoint (PI Function) .....................................................5-20
Boost Setting....................................................5-21, A-6
Display Scaling .........................................................A-6
Selection.................................................5-15, 5-19, A-6
Value.................................................................5-20, A-6
SHIFT/RESET Key...........................................................3-3
Shield Wire Grounding.......................................... 2-21, 2-28
Shipping Damage..............................................................1-3
Short Circuit Protection, Branch...............................E-2, E-3
Shunt Connector CN15 ...................................................2-25
Sinking/Sourcing Mode................................................. 2-26
Skip Frequency –– See Jump Frequency and Frequency
Limits ...............................................................5-27, A-9
Slave – See Modbus Communication Configuration.......D-2
Sleep Function – See PI Function, Sleep ................5-19, A-6
Snooze Function – See PI Function, Snooze. 5-21, 5-22, A-6
Soft Charge Contactor
Alarm........................................................................6-10
Checking ..................................................................6-21
Fault............................................................................6-7
Preventive Maintenance.............................................7-3
Soft Charge Resistor
Checking..................................................................6-21
Preventive Maintenance ............................................ 7-3
Soft CLA Selection........................................................ A-22
Soft Start — see S-Curve................................................. A-7
Software Number........................................................... A-27
Spare Parts ............................................................. F-1 to F-3
SPEC..........................................................................1-3, 1-4
Specifications....................................................................C-1
Design........................................................................ 1-4
General.......................................................................C-4
Standard Drive
208-240Vac.........................................................C-2
480Vac................................................................C-3
Nameplate........................................................... 1-3
Speed
Agreement ...........................................5-46, A-15, A-21
Control Accuracy.......................................................C-4
Range.........................................................................C-4
Speed Command – See also Frequency Reference
0-10Vdc ............................................................2-23, 4-9
4-20mA.............................................................2-23, 4-9
Limits....................................................................... 5-26
Loss Detection.........................................................5-43
Selection .............................................................4-6, 5-4
Setting Selection...................................................... 5-54
Signal Polarity ........................................................... 4-9
Troubleshooting..............................................6-15, 6-16
Speed Reference, Multiple (Multi-step Speed Operation) –
See Preset Speeds............................................................. A-8
Speed Search .................................................................. 5-11
Auto-Tuning ...........................................................5-59
Parameters ................................................................ A-5
Stall Prevention
Parameters .....................................................5-40, A-20
Specifications.............................................................C-4
Troubleshooting....................................................... 6-16
Start-up ...................................................................4-1 to 4-9
Assistance..........................................Inside Back Cover
Benchmark data ......................................................... 4-8
Preparation for........................................................... 4-2
Procedure................................................................... 4-5
Station Address (Modbus Control) ................................. D-5
Stop bits – See Modbus Communications ....................... D-1
STOP Indicator ................................................................ 3-5
Stop Method Selection (OH) ........................................ A-22
Stopping Method ....................................... 4-7, 5-6, 5-7, A-4
Coast to Stop.............................................................. 5-6
Coast w/Timer ........................................................... 5-7
DcInj to Stop.............................................................. 5-7
for External Fault from OPT Card.......................... A-11