EasyManuals Logo

YASKAWA Varispeed L7 User Manual

YASKAWA Varispeed L7
243 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #106 background imageLoading...
Page #106 background image
User Parameter Tables
4-39
4
Hardware Protection: L8
Param-
eter
Number
Name
Description
Setting
Range
Factory
Setting
Change
during
Opera-
tion
Control Methods
MEMO-
BUS
Register
Page
V/f
Open
Loop
Vector
Closed
Loop
Vector
Display
L8-02
Overheat pre-
alarm level
Sets the detection temperature
for the Inverter overheat detec-
tion pre-alarm in °C.
The pre-alarm detects when
the cooling fin temperature
reaches the set value.
50 to
130
75 °C* No A A A 4AEH 5-40
OH Pre-
Alarm Lvl
L8-03
Operation
selection after
overheat pre-
alarm
Sets the operation for when the
Inverter overheat pre-alarm
occurs.
0: Decelerate to stop using the
deceleration time C1-02.
1: Coast to stop
2: Fast stop in fast-stop time
C1-09.
3: Continue operation
(Monitor display only.)
A fault will be given in setting
0 to 2 and a minor fault will be
given in setting 3.
0 to 3 3 No A A A 4AFH 5-40
OH Pre-
Alarm Sel
L8-05
Input open-
phase protec-
tion selection
0: Disabled
1: Enabled (Detects power
supply open-phase, power
supply voltage imbalance
or DC bus electrostatic
capacitor deterioration.)
0 or 1 0 No A A A 4B1H 5-40
Ph Loss In Sel
L8-07
Output open-
phase protec-
tion selection
0: Disabled
1: Enabled, 1 Phase
Observatioin
2: Enabled, 2 and Phase
Observatioin
An output open-phase is
detected at less than 5% of
Inverter rated current.
When the applied motor capac-
ity is small compared to the
Inverter capacity, the detection
may not work properly and
should be disabled.
0 to 2 2 No A A A 4B3H 5-41
Ph Loss Out
Sel
L8-09
Ground pro-
tection selec-
tion
0:Disabled
1:Enabled
It is not recommended to use
another setting than factory
setting.
0 or 1 1 No A A A 4B5H 5-41
Ground Fault
Sel
L8-10
Cooling fan
control selec-
tion
Set the ON/OFF control for the
cooling fan.
0: ON when Inverter is
running only
1: ON whenever power is ON
0 or 1 0 No A A A 4B6H 5-42
Fan On/Off
Sel
L8-11
Cooling fan
control delay
time
Set the time in seconds to
delay turning OFF the cooling
fan after the inverter STOP
command is given.
0 to 300 60 s No A A A 4B7H 5-42
Fan Delay
Time
L8-12
Ambient tem-
perature
Sets the ambient temperature. 45 to 60 45 °CNo A A A4B8H5-42
Ambient
Temp
http://nicontrols.com

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the YASKAWA Varispeed L7 and is the answer not in the manual?

YASKAWA Varispeed L7 Specifications

General IconGeneral
BrandYASKAWA
ModelVarispeed L7
CategoryInverter
LanguageEnglish

Related product manuals