Agilent Technologies 6890 Plus User Manual

6 of 16 Jun 2001
Index
Index
Agilent 6890 Gas Chromatograph Service Manual
Adjust failure, 850-21
Bad cksum,850-20
Bad fact cal,850-20
Calib deleted, 830-6
Config changed, 830-3
Electrometer,850-4
Invalid pid,850-19
Invalid type, 850-17
I/O failure, 850-21
Makeup gas,820-3
Module rev,850-15
Temp sensor, 850-10
Temp too hot, 850-9
Type mismatch,850-18
Wrong module, 850-16
F inlet
Bad cksum
,850-20
Bad fact cal,850-20
Calib deleted, 830-5
Config changed, 830-4
Flow cal fail,830-8
Invalid pid,850-19
Invalid type, 850-18
I/O failure, 850-21
Module rev,850-16
Temp sensor, 850-11
Temp too hot, 850-10
Wrong module, 850-17
F TCD filament open,850-5
F TCD filament short,850-6
Fan
Injection port cover, removal
,410-16
Injection port, removal, 410-16
Motor replacement, 420-15
Pnematics area, removal, 410-18
Replacement,420-14
Fast heating oven,510-5
Fatal errors,860-1
Fault 200—Pneumatics shutdown: faulty board,
850-1
Fault 201—Pneumatics shutdown: faulty board,
850-1
Fault 203—Signal DSP faulty, 850-2
Fault 204—Sig DSP ROM broken,850-2
Fault 205—Sig DSP RAM broken, 850-3
Fault 206—Sig DSP registers,850-3
Fault 207—Sig DSP data corrupt,850-3
Fault 208—Signal path test failed,850-4
Fault 209—Signal path test failed,850-4
Fault 210—Signal path test failed,850-4
Fault 211—Signal path test failed,850-4
Fault 212—Front electrometer out of
specification
, 850-4
Fault 213—Back electrometer out of
specification
, 850-4
Fault 214—Front detector flame out,850-5
Fault 215—Back detector flame out,850-5
Fault 216—Front TCD filament open,850-5
Fault 217—Back TCD filament open, 850-5
Fault 218—Front TCD filament shorted,850-6
Fault 219—Back TCD filament shorted,850-6
Fault 220—Heater over current, 850-6, 850-8
Fault 222—Oven thermal shutdown, 850-8
Fault 223—Oven thermal shutdown, 850-9
Fault 224—Oven thermal shutdown, 850-9
Fault 225—Front detector thermal shutdown,
850-9
Fault 226—Front detector thermal shutdown,
850-10
Fault 227—Back detector thermal shutdown,
850-10
Fault 228—Back detector thermal shutdown,
850-10
Fault 229—Front inlet thermal shutdown, 850-10
Fault 230—Front inlet thermal shutdown, 850-11
Fault 231—Back inlet thermal shutdown, 850-11
Fault 232—Back inlet thermal shutdown, 850-12
Fault 233—Aux 1 thermal shutdown, 850-12
Fault 234—Aux 1 thermal shutdown, 850-12
Fault 235—Aux 2 thermal shutdown, 850-13
Fault 236—Aux 2 thermal shutdown, 850-13
Fault 237—No line interrupt thermal
shutdown
, 850-13
Fault 238—Faulty line interrupt thermal
shutdown
, 850-14
Fault 239—Mux ADC thermal shutdown, 850-14
Fault 240—Mux ADC offset value, 850-14
Fault 241—Line sense reading thermal
shutdown
, 850-14

Agilent Technologies 6890 Plus Specifications

General

Brand	Agilent Technologies
Model	6890 Plus
Category	Laboratory Equipment
Language	English