Automatic Divider-rounder model Syncro
7/79
Use and maintenance manual (translation of the original instructions) - MASA6_en_2 of 23/03/2021
1.2 GENERAL INSTRUCTIONS AND WARNINGS
Artezen S.r.l. declines any and all responsibility for injury to people or animals or damage to property caused by
the failure to observe the instructions, indications, recommendations, etc. contained in this manual and, in
particular, the following:
- Do not tamper with the guards and safety devices the machine is equipped with;
- Do not remove the guards and do not disable the safety devices provided with the machine, unless this is
really necessary; in this case, the machine must be stopped and the electrical power supply must be
disconnected until all the guards and safety devices have been correctly reassembled/reactivated and subject
to the adoption of measures aimed at reducing insofar as possible all the potential risks that might arise;
- Reassemble the guards and reactivate the safety devices as soon as the reasons that made their temporary
removal / deactivation necessary have been resolved;
- Do not use the machine for uses and/or with loads other than those indicated by the manufacturer;
- Carry out daily checks of the safety devices, including the level and conditions of the processing fluid (oil), and
the overall condition of the machine;
- Carry out a scrupulous daily cleaning of the machine and its parts
- Apply the necessary measures and caution in performing the daily work routine including adjustment,
cleaning, maintenance, etc. so that the machine or its parts are not activated by others, not even accidentally
- Observe the European Directives and Italian laws on workplaces, in particular (but not limited to) those on
safety warning signs, food hygiene, health and safety in the workplace, personal protective equipment, and
environmental protection;
- Respect the limits of the permitted climatic and use conditions: maximum relative ambient humidity 90%;
ambient temperature min. 15 °C; max. 40 °C; altitude above sea level 1000 m maximum. The temperature of
the oil in the hydraulic system should not be below + 15 °C.
- The employer must provide operators with adequate information and instruction, as well as practical training
on the correct and safe use of the machine.
- The operator must only wear tight fitting clothes, with no loose parts. They must never wear jackets, open
shirts, etc. or jewellery (rings, bracelets, necklaces, etc.); any long hair must be tied up (for example, under a
cap); work clothing must be adequate for maintaining the hygienic conditions of the food that is
handled/processed.
- Do not allow visitors, minors, or anyone who is not expressly authorised to enter the room where the
machine is used, or even approach the machine;
- where the machine is connected to other machinery or incorporated into a more complex system, the
manufacturer of said system resulting from the above connections or incorporation must analyse and evaluate
every further or greater risk deriving from such operation; take adequate measures to eliminate them or
reduce them as much as possible; comply with the requirements established by any pertinent Laws,
Directives, Standards, Regulations, etc. (definitely including Directive 2006/42/EC) and declare the complianec
of the system/unit with the provisions of the same
- Should it be necessary to replace parts of the machine, only use original spare parts by requesting them to
Artezen S.r.l.; in case of use of non-original spare parts, the manufacturer will consider itself exempt of any
and all liability for injury to persons or animals and damage to property that may occur as a result
- Any arbitrary modification made to the machine relieves the manufacturer of any and all responsibilities
for injuries to persons, animals, and damage to property that may occur as a result.
1.3 MAIN CASES IN WHICH THE COMPANY DECLINES ANY AND ALL LIABILITY
Artezen S.r.l. declines any and all liability for injury to persons or animals and damage to property, as well as
missed production that may result directly or indirectly from:
using the machine in a way that does not conform to the intended use, or in ways other than those
described herein
installation not in compliance with the procedures illustrated in this manual
use of the machine by personnel who are not sufficiently instructed, or where applicable, not
adequately trained in its correct use and safety measures
using energy sources that are inadequate or, in any case, different from those indicated in this manual
and/or in the attached documentation (ex. wiring diagrams)
lack of or inadequate maintenance, or maintenance not carried out according to the indication provided
herein;
partial compliance or failure to comply with the instructions in this manual
arbitrary modification of the original features and equipment of the machine without having received prior
formal authorization from the manufacturer
To Next Page
Loading...