Ascend T1 MAX series User Manual

MAX 4000 Series Hardware Installation Guide Preliminary November 4, 1998 xv
Figures
Figure 1-1 MAX base unit.............................................................................................. 1-2
Figure 1-2 Redundant MAX base unit ........................................................................... 1-2
Figure 1-3 DC power source on the MAX 4000 and the Redundant MAX 4000.......... 1-2
Figure 1-4 Host/6 card.................................................................................................... 1-3
Figure 1-5 ISDN BRI network-interface or terminal-interface card.............................. 1-4
Figure 1-6 Multiband inverse-multiplexing two-port card............................................. 1-4
Figure 1-7 Series56 Digital modem card........................................................................ 1-5
Figure 1-8 V.110 card..................................................................................................... 1-5
Figure 1-9 PIAFS card.................................................................................................... 1-6
Figure 1-10 IDSL card...................................................................................................... 1-6
Figure 2-1 MAX units installed in a rack....................................................................... 2-2
Figure 2-2 Inserting an expansion card into a MAX slot............................................... 2-3
Figure 2-3 Tightening slot card thumbscrews................................................................ 2-4
Figure 2-4 Dimensions of the single power supply unit................................................. 2-5
Figure 2-5 Dimensions of the redundant power supply unit.......................................... 2-5
Figure 2-6 Mounting the MAX in a rack........................................................................ 2-6
Figure 2-7 DC power source .......................................................................................... 2-7
Figure 2-8 One set of links for each E1 port.................................................................. 2-8
Figure 2-9 Location of the MAX LEDs......................................................................... 2-9
Figure 2-10 Location of the LEDs on the Redundant MAX.......................................... 2-11
Figure 2-11 Ethernet interface LEDs on MAX back-panel............................................ 2-12
Figure 3-1 Quickstart setup............................................................................................ 3-2
Figure 3-2 Incoming call routing using inband signaling and hunt groups.................... 3-3
Figure 3-3 Incoming call routing using ISDN signaling and hunt groups..................... 3-4
Figure 3-4 MAX T1 configuration interface.................................................................. 3-9
Figure 3-5 Front-panel indicator lights......................................................................... 3-15
Figure 3-6 Testing the WAN by dialing into and out from the MAX.......................... 3-23
Figure 3-7 Quickstart set up......................................................................................... 3-25
Figure 3-8 Incoming call routing using R2 signaling and hunt groups........................ 3-26
Figure 3-9 Incoming call routing using ISDN signaling and hunt groups................... 3-27
Figure 3-10 MAX E1 configuration interface................................................................ 3-31
Figure 3-11 Front-panel indicator lights......................................................................... 3-38
Figure 3-12 Testing the WAN by dialing into and out from the MAX.......................... 3-46
Figure 4-1 MAX 4000 Series configuration menus....................................................... 4-2
Figure 4-2 Slot and port numbering in the MAX 4000 series........................................ 4-9
Figure C-1 Control-monitor and MIF palmtop port and cable ....................................... C-3
Figure C-2 RJ-48C/RJ-48C crossover cable................................................................... C-7
Figure C-3 RJ-48C/RJ-48C straight-through cable specifications.................................. C-8
Figure C-4 RJ-48C/DA-15 straight-through cable.......................................................... C-9
Figure C-5 RJ-48C/DA crossover cable ....................................................................... C-10
Figure C-6 RJ-48C/Bantam straight-through cable ...................................................... C-11
Figure C-7 RJ-48C/RJ-48C crossover cable................................................................. C-14
Figure C-8 RJ-48C/RJ-48C straight-through cable specifications................................ C-15

Ascend T1 MAX series Specifications

General

Brand	Ascend
Model	T1 MAX series
Category	Network Router
Language	English