Autronica AutroGuard Multicriteria Protector V-430 Series - Page 126

126 pages

To Previous Page

Main Page

Table of Contents3
Introduction8
Scope8
The Manual8
Target Audience8
Reference Documentation8
Downloading Technical Documents8
Technical Terms and Abbreviations9
Document Revision Log10
Safety11
Important Safety Information11
Intended Use12
Safety Notice12
Safety Regulations12
National Standards and Regulations12
Mounting, Installation, Commissioning and Maintenance13
Modifications to the Products13
Compliance with Standards and Directives13
Recommendations for Latest Available Firmware and Operating System13
Environment Compatibility14
Recycling14
Disposal14
Protector Overview15
Product Decription15
Details for Ordering16
Ordering Information Accessories18
Ordering Information Autroguard Retro Variants18
Labeling19
Marking on Protector (Bottom)20
Marking on Protector Base (Inside)21
Marking on Protector Top, EX Only22
QR Code and Data Matrix Code23
QR and Data Matrix Code Information23
QR Code Placement on Protector23
Data Matrix Code Placement on Protector Base's Tagholder24
Tag Holder for Labels24
Dimensions and Outlines25
Protector Base25
Protector with Visual Alarm Device (VAD)25
Protector Without Visual Alarm Device (VAD)26
Protector for Retrofit Mounting Onto BWA-100/BWA-101 (Height)26
Technical Specifications27
Protector and Base27
Integrated Sounder28
Tones29
Sound Pressure Levels for Tones30
Integrated VAD - Current Consumption35
Integrated VAD and Sounder - Current Consumption36
Functional Description37
General37
Chamber Design37
Dyfi 3D38
DYFI 3D - Particle/Smoke Signature Analysis38
DYFI 3D - Dynamic Filtering39
Sensitivity Classes for Environmental Adaptivity40
Operation Classes40
Heat Response Categories41
Selfverify® 2.0 Function42
Cover Detection42
Protector "Alive Signal43
LED Behavior43
Visual Alarm Device (VAD)44
Compliance with EN54-2344
Coverage Volume44
Category C - Ceiling Mounted Devices45
Category O46
Visual Alarm Device (VAD) Intensity46
Consideration Factors for VAD Sensitivity Settings46
VAD Intensity Settings46
VAD Intensity - White VAD and Red VAD47
Flash Rate47
Audible Alarm Devices48
General48
Sound Pressure Level48
Sound and Pulse Patterns48
Planning49
Reference to National/Local Regulations49
Enviromental Requirements49
Location / Required Space49
Area Coverage and Monitoring Distance50
Smoke Detection50
Heat Detection51
Current Consumption on Detection Loop52
Mounting Instructions53
Cable Entries/Exits on the Protector Base53
Cable Entry for Concealed Conduit Wiring53
Cable Entries/Knockout Stampings for Surface-Mounted Wiring54
Mounting the Protector Base55
Considerations before Mounting55
Template for Marking and Drilling Holes56
Mounting for Concealed Conduit Wiring57
Mounting Onto a Ceiling Box / Wall Box58
Mounting Onto a Conduit Box59
Mounting for Surface-Mounted Wiring61
Connecting Loop Cables62
Cable Requirements62
Wire Routing Arrangement Inside Protector Base63
Wire Insulation Stripping64
Spring Cage Connection65
Connections - Overview66
Loop Connections66
LED Connection67
Branch-Offs67
Alignment Marks on the Protector69
Mounting the Protector Onto the Base70
Locking/Unlocking the Protector to the Base71
Removing the Protector from the Base72
Retrofit Mounting Onto Existing Autrosafe Base72
Bwa-100/Bwa-10172
Labeling the Protector Base / Tag Holder74
Protector Cover74
Preparing for Configuration75
Introduction75
Tools Requirements75
Alternative Ways of Identifying Serial Numbers75
Alternative a - Using QR Code Reader (Recommended)75
Alternative B - Using the Rip off Label Inside the Autroguard Base76
Labeling Bases with Tag Name Labels76
Alternative a - Using a QR Code Reader77
Alternative B - Using the Rip off Label77
Scanning each Loop with AS200077
Generating an Excel File78
Merging Tag Names, Serial Numbers and LSI78
Autrosafe Configuration Tool79
Troubleshooting79
Configuration Recommendations80
Introduction80
Hotel Rooms81
Apartments81
Freezers and Cold Stores82
Clean Rooms and Computer Rooms82
Configuration for Autrosafe86
Introduction86
Autrosafe Configuration Tool Requirements86
Site Configuration System Settings87
Detector Defaults - LED on Alarm/Led Alive Blink87
Sound and Pulse Patterns88
Adding System Units89
Autroguard Default Settings91
Set Autroguard Defaults Menu91
Multi92
Ex/S93
Sounder93
Visual Alarm Device (VAD)94
Postfix94
Autroguard Settings for Multiple Protectors95
Autroguard Individual Settings96
Fire Alarm Devices96
Automatic Test Mode96
Cover Detection Sensitivity97
Heat Response Categories97
Operation Classes98
Sensitivity Settings for Environmental Adaptivity98
Visual Alarm Device (VAD)99
Sound Pressure Level - Sounders101
Matching Protectors/Bases with Autrosafe Configurations102
Configuration for Autroprime103
Introduction103
Autroprime Software Requirements103
Global Settings104
Sound Patterns104
Visual Alarm Device (VAD)104
Individual Settings105
Operation Class Day Mode105
Heat Response Category Day Mode106
Sensitivity Class Day Mode106
Operation Class Night Mode106
Heat Response Category Night Mode107
Sensitivity Class Night Mode107
Enable Automatic Test Mode107
Use LED Alive Blink108
Use Blink on Alarm108
External Output Follow Alarm108
Cover Detection Sensitivity108
Testing and Maintenance109
Selfverify® 2.0 Function109
Visual Inspection109
Manual Testing110
Introduction110
Test Equipment110
Automatic Test Mode110
Cleaning Procedure112
Replacing a Protector (Hot Swap)112
Calibrating the Cover Detection Sensor113
Method A: Re-Calibrating Using a Protector Cover113
Method B: Re-Calibrating Using AS2000 Loop Diagnostic Tool114
Accessories116
Locking Tool for Locking the Protector to the Base116
QR Code Reader116
WAS-2000 and AS2000 Loop Diagnostic Tool117
Cover117
Air Duct Sampling Unit118
Air Duct Sampling Unit - Stainless Steel119
Conduit Box120
Telescope Removal Tool121
Ground Device121
Test Gas122
Testfire / solo 365 Test Tool122
Appendix123
UL Regulatory Information123
Index124

Autronica AutroGuard Multicriteria Protector V-430 Series - Page 126

Table of Contents

Related product manuals