2-16
Confidential
Error
codes
Problem
Refer
to:
Error
codes
Problem
Refer
to:
50
The drum unit reached the end
of life. (Printable)
2-35 68
An unidentified error occurred.
2-41
51 An unidentified error occurred. 2-36 69 An unidentified error occurred. 2-41
52
An unidentified error occurred.
2-36 6A
Fuser unit error. (The center
thermistor does not detect 60°C
within in the specified time.)
2-42
53
An unidentified error occurred.
2-36 6B
Fuser unit error. (The center
thermistor does not detect 100°C
within in the specified time.)
2-42
54
An unidentified error occurred.
2-36 6C
Fuser unit error. (The center
thermistor detects 270°C or
higher temperature for 1 second.)
2-42
55
An unidentified error occurred.
2-36 6D
Fuser unit error. (The center
thermistor detects 60°C or lower
temperature for 1 second during
ready state or printing.)
2-42
56 The fuser cover is open. 2-36
6E An unidentified error occurred. 2-42
57
Paper is jammed in the duplex
paper feed path. 2-37 6F
Fuser unit error. (The center and
side thermistors detect extremely
high temperature.)
2-43
58
Any of errors 6A to 6D, 6F, 76 or 78
occurred when the power was
turned ON or machine goes back to
the ready state from sleep mode.
2-37 70
An unidentified error occurred.
2-43
59
Error code displayed to prompt the
operator to leave the machine for a certain
time when power was turned OFF and
then ON again after error 58 occurred.
2-38 71
Laser unit error.
2-44
5A
An unidentified error occurred.
2-39 72
Failed to detect the beam by BD
sensor of the laser unit.
2-44
5B An unidentified error occurred. 2-39 73 An unidentified error occurred. 2-44
5C An unidentified error occurred. 2-39 74 An unidentified error occurred. 2-44
5D
An unidentified error occurred.
2-39 75
The internal temperature
reached its upper limit.
2-45
5E
An unidentified error occurred.
2-39 76
Fuser unit error. (The center
thermistor detects the sharp
temperature rise.)
2-45
5F
An unidentified error occurred.
2-39 78
Fuser unit error. (The center
thermistor detects the sharp
temperature fall.)
2-45
60
An unidentified error occurred.
2-39 7A
Synchronized signal of the main
motor cannot be detected.
2-45
61 An unidentified error occurred. 2-39 7B An unidentified error occurred. 2-46
62 An unidentified error occurred. 2-39 7C An unidentified error occurred. 2-46
63
The number of rotations of the developer
roller reached the upper limit when stop
mode is set for the toner cartridge.
2-40 7D
Detected unusual discharge of
the corona wire due to dirt on
the drum unit.
2-46
64 An unidentified error occurred. 2-40 7E An unidentified error occurred. 2-47
65
An unidentified error occurred.
2-40 7F
FAX paper size is incorrect.
(Menu setting)
2-47
66
An unidentified error occurred.
2-40 80
FAX paper size is incorrect.
(The actually loaded paper is small)
2-47
67
The number of rotations of the developer
roller will reach the upper limit when stop
mode is set for the toner cartridge.
2-41 81
An unidentified error occurred.
2-47