EasyManuals Logo

Cisco 7962G Administration Guide

Cisco 7962G
235 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #93 background imageLoading...
Page #93 background image
4-19
Cisco Unified IP Phone Administration Guide for Cisco Unified Communications Manager 7.1
OL-18913-01
Chapter 4 Configuring Settings on the Cisco Unified IP Phone
Device Configuration Menu
SIP General Configuration Menu
The SIP General Configuration menu displays information about the configurable SIP parameters on the
phone. Table 4-8 describes the options in this menu.
Related Topics
Displaying a Configuration Menu, page 4-2
Device Configuration Menu, page 4-16
Table 4-8 SIP General Configuration Menu Options
Option Description To Change
Preferred CODEC Displays the CODEC to use when a call is initiated. This
value will always be set to none.
Display only—cannot configure.
Out of Band DTMF Displays the configuration of the out-of-band signaling
(for tone detection on the IP side of a gateway). The
Cisco Unified IP phone (SIP) supports out-of-band
signaling by using the AVT tone method. This value will
always be set to avt.
Display only—cannot configure.
Register with Proxy This value will always be set to Yes. Display only—cannot configure.
Register Expires Displays the amount of time, in seconds, after which a
registration request expires.
From Cisco Unified
Communications Manager
Administration, choose Device >
Device Settings > SIP Profile.
Phone Label Displays the text that is displayed on the top right status
line of the LCD on the phone. This text is for end-user
display only and has no effect on caller identification or
messaging. This value will always be set to null.
Display only—cannot configure.
Enable VAD This value is set to No by default. From Cisco Unified
Communications Manager
Administration, choose Device >
Device Settings > SIP Profile.
Start Media Port Displays the start Real-Time Transport Protocol (RTP)
range for media.
From Cisco Unified
Communications Manager
Administration, choose Device >
Device Settings > SIP Profile.
End Media Port Displays the end Real-Time Transport Protocol (RTP)
range for media.
From Cisco Unified
Communications Manager
Administration, choose Device >
Device Settings > SIP Profile.
NAT Enabled Displays if Network Address Translation (NAT) is
enabled. This value will always be set to false.
Display only—cannot configure.
NAT Address Displays the WAN IP address of the NAT or firewall
server. This value will always be set to null.
Display only—cannot configure.
Call Statistics This value is set to No by default. From Cisco Unified
Communications Manager
Administration, choose Device >
Device Settings > SIP Profile.

Table of Contents

Other manuals for Cisco 7962G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7962G and is the answer not in the manual?

Cisco 7962G Specifications

General IconGeneral
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Case materialABS
Product colorBlack, Grey
Wall mountableYes
BluetoothNo
Security algorithms128-bit AES, 802.1x RADIUS
Networking standardsIEEE 802.1Q, IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN data rates10, 100 Mbit/s
Ethernet LAN interface typeFast Ethernet
Ethernet LAN (RJ-45) ports2
Voice codecsG.711, G.711a, G.722, G.729A, G.729ab, iLBC
Volume controlDigital
Display diagonal5 \
Display resolution320 x 222 pixels
Display number of colorsMonochrome
Caller ID-
Lines quantity- lines
Phonebook capacity- entries
Storage temperature (T-T)-10 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Number of handles included1 pc(s)
Weight and Dimensions IconWeight and Dimensions
Depth203.2 mm
Width266.7 mm
Height152.4 mm
Weight1600 g

Related product manuals