D-Link DWS-3160-24TC - Page 113

DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
109
<value 0-7> | replace_dscp_with <value 0-63> | counter [enable | disable]} | deny]
{time_range <range_name 32>} | delete access_id <value 1-128>]
Parameters
profile_id
- Specifies the index of the egress access list profile.
<value 1-4> - Enter the profile ID used here. This value must be between 1 and 4.
profile_name - Specifies the name of the profile.
<name 1-32>
- Enter the profile name here. This name can be up to 32 characters long.
add - Specifies to add a profile or rule.
access_id - Specifies the index of the access list entry. If the auto_assign option is selected, the
access ID is automatically assigned.
auto assign - Specifies that the access ID will be configured automatically.
<value 1-128>
- Enter the access ID used here. This value must be between 1 and 128.
ethernet - Specifies an Ethernet egress ACL rule.
vlan - (Optional) Specifies the VLAN name.
<vlan_name 32> - Enter the VLAN name used for this configuration here. This name can be
up to 32 characters long.
vlanid - Specifies a VLAN ID.
<vlanid 1-4094> - Enter the VLAN ID used for this configuration here. This value must be
between 1 and 4094.
source_mac - (Optional) Specifies the source MAC address.
<macaddr> - Enter the source MAC address used here.
mask - Specifies that source MAC mask used.
<macmask> - Enter the source MAC mask value here.
destination_mac - Specifies the destination MAC address.
<macaddr> - Enter the destination MAC address used here.
mask - Specifies that destination MAC mask used.
<macmask> - Enter the destination MAC mask value here.
802.1p - (Optional) Specifies the value of the 802.1p priority tag. The priority tag ranges from 1 to
7.
<value 0-7> - Enter the 802.1p priority tag used here.
ethernet_type - (Optional) Specifies the Ethernet type.
<hex 0x0-0xffff> - Enter the Ethernet type mask used here.
ip - Specifies an IP egress ACL rule.
vlan - (Optional) Specifies the VLAN name.
<vlan_name 32> - Enter the VLAN name used for this configuration here. This name can be
up to 32 characters long.
vlanid - Specifies a VLAN ID.
<vlanid 1-4094> - Enter the VLAN ID used for this configuration here. This value must be
between 1 and 4094.
mask - (Optional) Specifies the mask used.
<hex 0x0-x0fff> - Enter the mask value used here.
source_ip - (Optional) Specifies an IP source address.
<ipaddr> - Enter the source IP address used here.
mask - Specifies the source IP address used here.
<netmask> - Enter the source network mask here.
destination_ip - (Optional) Specifies an IP destination address.
<ipaddr> - Enter the destination IP address used here.
mask - Specifies the destination IP address used here.
<netmask>
- Enter the destination network mask here.
dscp - (Optional) Specifies the value of DSCP. The DSCP value ranges from 0 to 63.
<value 0-63> - Enter the DSCP value used here. This value must be between 0 and 63.
icmp - (Optional) Specifies that the following parameters configured will apply to the ICMP
configuration.
type - Specifies that the rule will apply to the ICMP type traffic value.
<value 0-255> - Enter the ICMP traffic type value here. This value must be between 0 and
255.