DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
789
index - Specifies the configured WEP transfer key index. The number of characters
required depends on the configured WEP key type and length.
<int 1-4> - Enter the configured WEP transfer key ID used here. This value must be
between 1 and 4.
value - Specifies the WEP key itself, entered in ASCII or HEX format.
<string> - Enter the WEP key here.
clear - Specifies to clear the WEP key entered.
length - Specifies the WEP key length.
64 - Specifies that the WEP key length will be set as 64 bit.
128 - Specifies that the WEP key length will be set as 128 bit. This is the default option.
default - Specifies that the default option will be used.
type - Specifies the WEP key type.
ascii - Specifies that the WEP key type will be set as ASCII.
hex - Specifies that the WEP key type will be set as HEX. This is the default option.
default - Specifies that the default option will be used.
tx_key - Specifies the WEP key index used for encryption on the network. This value is
applicable only when the security mode is configured for WEP shared-key authentication
and encryption.
<int 1-4> - Enter the WEP key index used here. This value must be between 1 and 4. The
default value is 1.
- Specifies that the default value will be used.
wpa - Specifies that the security mode will be set to WPA.
ciphers - Specifies the WPA cipher suites supported on the network.
ccmp - Specifies that CCMP encryption will be used with WPA.
tkip - (Optional) Specifies that both CCMP and TKIP encryption will be used with WPA.
This is the default option.
tkip - Specifies that TKIP encryption will be used with WPA.
default - Specifies that the default option will be used.
key - Specifies the WPA shared-key. This is an alphanumeric string in the range 8-64
characters. The configured key is used when the network security mode is set as WPA
shared-key.
value - Specifies the shared secret key for WPA Personal.
<string> - Enter a string of at least 8 characters to a maximum of 63 characters.
Acceptable characters include upper and lower case alphabetic letters, numeric
digits, and special symbols like '@' and '#'.
clear - Specifies the clear the key entered.
versions - Specifies the WPA version(s) supported on the network. One or both parameters
must be specified.
wpa - Specifies the WPA version will be set as WPA.
wpa2 - (Optional) Specifies the WPA version will be set as WPA and WPA2. This is the
default option.
wpa2 - Specifies the WPA version will be set as WPA2.
default - Specifies that the default option will be used.
wpa2 - Specifies that the security mode will be set to WPA2.
key_chching - Specifies the length of time a Pairwise Master Key (PMK) will be cached by an
AP for either client roaming or key forwarding.
holdtime - Specifies the WPA2 key caching hold time.
<int 1-1440> - Enter the WPA2 key caching hold time here. This value must be
between 1 and 1440 minutes. The default value is 10 minutes.
default - Specifies that the default value will be used.
pre_authentication - Specifies that WPA2 pre-authentication support for client roaming will
be configured.
state - Specifies the state of WPA2 pre-authentication support for client roaming.
enable - Specifies that WPA2 pre-authentication support for client roaming will be
enabled. This is default option.
disable - Specifies that WPA2 pre-authentication support for client roaming will be
disabled.
limit - Specifies the WPA2 pre-authentication limit for the network. This specifies a limit on the
number of APs within the peer group to which one client is allowed to pre-authenticate.
<int 0-192> - Enter the WPA2 pre-authentication limit, for the network, here. This value
To Next Page
Loading...
