<name 1-31> - Enter the IPv6 ACL named used here. This name can be up to 31 characters
long. This parameter is a case-sensitive alphanumeric string uniquely identifying the IPv6
access list.
rename - Specifies to rename the specified IPv6 ACL.
<name 1-31> - Enter the IPv6 ACL named used here. This name can be up to 31
characters long. This parameter is a case-sensitive alphanumeric string uniquely
identifying the IPv6 access list.
add_rule - Specifies to create a new rule for an IPv6 ACL.
<value 1-10> - Enter the new rule number here. This value must be between 1 and 10.
type - Specifies what action should be taken if a packet matches the rule's criteria. The
possible values are Permit or Deny.
deny - Specifies that the action that will take place, if a packet matches the rule's criteria, is
deny.
permit - Specifies that the action, that will take place, if a packet matches the rule's criteria,
is permit.
match_every - Specifies to match every packet. Valid values are true or false.
true - Specifies that every packet is considered to match the selected ACL Rule.
false - Specifies that it is not mandatory for every packet to match the selected ACL Rule.
src_ipv6 - Specifies the source IPv6 address of the IPv6 ACL rule.
src_prefix - Specifies the source IPv6 prefix of the IPv6 ACL rule.
<ipv6addr> - Enter the source IPv6 prefix value used here.
src_prefix_length - Specifies the source IPv6 prefix length of the IPv6 ACL rule.
<int 1-128> - Enter the source IPv6 prefix length of the IPv6 ACL rule here.
dst_ipv6 - Specifies the destination IPv6 address of the IPv6 ACL rule.
dst_prefix - Specifies the destination IPv6 prefix of the IPv6 ACL rule.
<ipv6addr> - Enter the destination IPv6 prefix value used here.
dst_prefix_length - Specifies the destination IPv6 prefix length of the IPv6 ACL rule.
<int 1-128> - Enter the destination IPv6 prefix length of the IPv6 ACL rule here.
src_layer4_port - Specifies the source Layer 4 port match condition for the IP ACL rule.
domain - Specifies that the source Layer 4 port match condition will use to port number of
the service called Domain.
echo - Specifies that the source Layer 4 port match condition will use to port number of the
service called Echo.
ftp - Specifies that the source Layer 4 port match condition will use to port number of the
service called FTP.
ftpdata - Specifies that the source Layer 4 port match condition will use to port number of
the service called FTP Data.
http - Specifies that the source Layer 4 port match condition will use to port number of the
service called HTTP.
smtp - Specifies that the source Layer 4 port match condition will use to port number of the
service called SMTP.
snmp - Specifies that the source Layer 4 port match condition will use to port number of
the service called SNMP.
telnet - Specifies that the source Layer 4 port match condition will use to port number of
the service called TELNET.
tftp - Specifies that the source Layer 4 port match condition will use to port number of the
service called TFTP.
other - Specifies to use a custom port number that the source Layer 4 port match condition
will use.
<int 0-65535> - Enter the custom source Layer 4 port number used here. This value
must be between 0 and 65535.
dst_layer4_port - Specifies the destination Layer 4 port match condition for the IP ACL rule.
domain - Specifies that the destination Layer 4 port match condition will use to port
number of the service called Domain.
echo - Specifies that the destination Layer 4 port match condition will use to port number
of the service called Echo.
To Next Page
Loading...
