D-Link DWS-3160-24TC - Page 843

DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
839
telnet - Specifies that the destination Layer 4 port match condition will use to port number
of the service called TELNET.
tftp - Specifies that the destination Layer 4 port match condition will use to port number of
the service called TFTP.
other - Specifies to use a custom port number that the destination Layer 4 port match
condition will use.
<int 0-65535> - Enter the custom destination Layer 4 port number used here. This
value must be between 0 and 65535.
protocol - Specifies the protocol to filter for a named IPv6 ACL rule, identified by number. The
protocol number is a standard value assigned by IANA and is interpreted as an integer
from 1 to 255. You can use the protocol number or you Specifies a protocol keyword.
ip - Specifies that the protocol, used to filter for a named IPv6 ACL rule, is IP.
icmp - Specifies that the protocol, used to filter for a named IPv6 ACL rule, is ICMP.
igmp - Specifies that the protocol, used to filter for a named IPv6 ACL rule, is IGMP.
tcp - Specifies that the protocol, used to filter for a named IPv6 ACL rule, is TCP.
udp - Specifies that the protocol, used to filter for a named IPv6 ACL rule, is UDP.
other - Specifies a custom protocol number to use in the named IPv6 ACL rule.
<int 1-255> - Enter the custom protocol number, used to filter for a named IPv6 ACL
rule, here. This value must be between 1 and 255.
flow_label - Specifies the value specified for IPv6 Flow Label.
<uint 0-1048575> - Enter the IPv6 Flow Label value here. This value must be between 0
and 1048575.
ip_dscp - Specifies the IPv6 DiffServ Code Point (DSCP) field. The DSCP is defined as the
high-order six bits of the Service Type octet in the IPv6 header. The IPv6 DSCP is
configured by a possible selection of one of the DSCP keywords or a numerical values.
af11 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af11'.
af12 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af12'.
af13 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af13'.
af21 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af21'.
af22 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af22'.
af23 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af23'.
af31 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af31'.
af32 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af32'.
af33 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af33'.
af41 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af41'.
af42 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af42'.
af43 - Specifies that the IPv6 DiffServ Code Point value will be set as 'af43'.
be - Specifies that the IPv6 DiffServ Code Point value will be set as 'be'.
cs0 - Specifies that the IPv6 DiffServ Code Point value will be set as 'cs0'.
cs1 - Specifies that the IPv6 DiffServ Code Point value will be set as 'cs1'.
cs2 - Specifies that the IPv6 DiffServ Code Point value will be set as 'cs2'.
cs3 - Specifies that the IPv6 DiffServ Code Point value will be set as 'cs3'.
cs4 - Specifies that the IPv6 DiffServ Code Point value will be set as 'cs4'.
cs5 - Specifies that the IPv6 DiffServ Code Point value will be set as 'cs5'.
cs6 - Specifies that the IPv6 DiffServ Code Point value will be set as 'cs6'.
cs7 - Specifies that the IPv6 DiffServ Code Point value will be set as 'cs7'.
ef - Specifies that the IPv6 DiffServ Code Point value will be set as 'ef'.
other - Specifies that a custom IPv6 DiffServ Code Point value will be used.
<int 0-63> - Enter a custom IPv6 DiffServ Code Point value here. This value must be
between 0 and 63.
flow_label - Specifies the value specified for IPv6 Flow Label.
<uint 0-1048575> - Enter the IPv6 Flow Label value here. This value must be between 0
and 1048575.
Restrictions
Only Administrators can issue this command.