D-Link DWS-3160-24TC - Page 846

DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
842
<value 0-7> - Enter the CoS value, for this rule, here. This value must be between 0 and 7.
vlan - Specifies the VLAN identifier value for this rule.
<vlanid 0-4095> - Enter the VLAN ID used here. This value must be between 0 and 4095.
del_rule - Specifies to delete a specified rule from a MAC ACL.
<value 1-12> - Enter the specific MAC ACL rule value, that will be deleted, here. This
value must be between 1 and 12.
edit_rule - Specifies to update a specified rule of a MAC ACL.
<value 1-12> - Enter the specific MAC ACL rule value, that will be updated, here. This
value must be between 1 and 12.
type - Specifies what action should be taken if a packet matches the rule's criteria. The
possible values are Permit or Deny.
deny - Specifies that the action, that will be taken if a packet matches the rule's criteria, is
deny.
permit - Specifies that the action, that will be taken if a packet matches the rule's criteria, is
permit.
match_every - Specifies to match every Layer 2 MAC packet.
true - Specifies that every packet is considered to match the selected ACL Rule.
false - Specifies that it is not mandatory for every packet to match the selected ACL Rule.
srcmac - Specifies the source MAC address for this rule, to compare against an Ethernet
frame.
mac - Specifies the source MAC address for this rule, to compare against an Ethernet
frame.
<macaddr> - Enter the Source MAC address, for this rule, here.
mask - Specifies the source MAC address mask for this rule, indicating which bits in the
source MAC to compare against an Ethernet frame.
<macmask> - Enter the source MAC address mask, for this rule, here.
dstmac - Specifies that the destination MAC address for this rule, will be configured.
mac - Specifies the destination MAC address for this rule, to compare against an Ethernet
frame
<macaddr> - Enter the destination MAC address, for this rule, here.
mask - Specifies the destination MAC address mask for this rule, Specifiesing which bits in
the destination MAC to compare against an Ethernet frame.
<macmask> - Enter the destination MAC address mask used here.
ethertypekey - Specifies the Ethertype keyword or custom value for this rule and to compare
against an Ethernet frame. The Ethertype may be specified as either a keyword or a four-
digit hexadecimal value from 0x0600-0xFFFF. Each of these keywords translates into its
equivalent Ethertype value(s).
appletalk - Specifies that the Ethertype keyword is 0x809B.
arp - Specifies that the Ethertype keyword is 0x0806.
ibmsna - Specifies that the Ethertype keyword is 0x80D5.
ipv4 - Specifies that the Ethertype keyword is 0x0800.
ipv6 - Specifies that the Ethertype keyword is 0x86DD.
ipx - Specifies that the Ethertype keyword is 0x8037.
mplsmcast - Specifies that the Ethertype keyword is 0x8848.
mplsucast - Specifies that the Ethertype keyword is 0x8847.
netbios - Specifies that the Ethertype keyword is 0x8191.
rarp - Specifies that the Ethertype keyword is 0x8035.
user_value - Specifies a custom user value for the Ethertype keyword.
<hex 0x600-0xffff> - Enter a user custom Ethertype keyword value here. This value
must be between 0x600 and 0xffff.
cos - Specifies the CoS (802.1p user priority) value for this rule.
<value 0-7> - Enter the CoS value, for this rule, here. This value must be between 0 and 7.
vlan - Specifies the VLAN identifier value for this rule.
<vlanid 0-4095> - Enter the VLAN ID used here. This value must be between 0 and 4095.
Restrictions
Only Administrators can issue this command.