Epson Stylus CX4900 User Manual

EPSON Stylus CX4900/CX4905/CX5000/DX5000/DX5050/CX5900/CX6000/DX6000/DX6050 Revision A
PRODUCT DESCRIPTION Control Panel 61
1.9.4.3 Memory Card Insertion/Ejection
The functions of this unit caused by memory card insertion or ejection are described in
the following table.
1.9.4.4 Connection/Removal of DSC
Note *1: For Stylus CX4900/CX4905/CX5000/DX5000/DX5050; LED panel will show ‘P’
and Change to “Print All/DPFOF”
*2: For Stylus CX4900/CX4905/CX5000/DX5000/DX5050; “Print All/DPFOF”
1.9.4.5 Low Power Panel Mode
Without any panel operation for 13*
1
/15*
2
minutes while the printer and scanner unit
are in standby status, this unit moves into the low power panel mode in which power
consumption for the panel decreases. This unit recovers from that mode by pushing any
button but Power Button or printing/scanning by the computer. This unit is turned off
by pushing Power Button in that mode.
Note *1: Stylus CX5900/CX6000/DX6000/DX6050
*2: Stylus CX4900/CX4905/CX5000/DX5000/DX5050
1.9.4.6 Adjust Lever Function
If paper thickness lever is in wrong position, the printer displays “PG position warning”.
l
Note *1: Stylus CX4900/CX4905/CX5000/DX5000/DX5050
*2: Stylus CX5900/CX6000/DX6000/DX6050
Table 1-55. Memory Card Insertion/Ejection
Action Function
Card Insertion
• Recognize the card and light Card Access LED if it is right.
• The LED blinks while memory access occurs to the memory card.
• The Power LED blinks during the card recognition.
• Return from the low power panel mode.
Card Ejection
• Turn off Card Access LED.
• Stop print job while memory card pri
nt is in process and eject paper.
• Clear memory card error if memory card is wrong.
Table 1-56. Connection/Removal of DSC
Action Function
Connect
the DSC
to this unit
with USB
cable
This unit moves to a DSC direct mode after a device is confirmed for DSC direct,
when a device is connected to EXT. I/F (USB Host). It won’t move to DSC direct
mode when it shows general printing mode or error. It moves to DSC direct mode
when it finished printing or error status has been resolved. (Errors that is related
with memory card, index sheet or PG will be automatically canceled and it moves to
DSC direct mode. Ink-low status will be also ignored.).
“Camera Connected” icon will be displayed
with LCD and Change to “Print
Select”*
1
when connection was confirmed, not when it moves to DSC direct mode.
If the DSC direct device was connected to EXT I/F and any error has occurred on
confirmation, it shows DSC direct error.
If this unit was on power save mode and DSC direct device was connected, this unit
will be back to usual status and then it confirms connection.
Remove
the DSC
from this
unit
This unit moves to “Memory card print” mode and select and light “Print Select”*
2
when condition where device recognition was carried out normally for DSC direct.
During the printing from a device for DSC direct, this unit stops a printin
g and
moves to “Memory card print” mode and select and light “Print Select”.*
2
When this unit is displaying “DSC direct error”, this unit cancel it error and returns
it in condition of before connection.
Table 1-57. Low Power Panel Mode
Action Function
Transition to
low p
ower
mode
• Turn off (LCD and *
1
) all LEDs except for Power LED and Card Access LED.
• Blink Decimal Point LED slowly.*
2
• No move in error status except for memory card error, index sheet error and PG
error.
• Ejecting of memory card or accessing it by PC has no effect on low power
mode.
Recovery
from low
power mode
• Recall the panel status as that before moving to low power panel mode.
• Inserting or ejecting of memory card or accessing it by PC has no effect on low
power mode.
Table 1-58. Adjust Lever Function
Adjust lever
status
Function
PG open
(Di
splayed “H”)*
1
(“H” to “L”) *
2
• “H” will be displayed with 7 Segment LED for about 3 seconds just
after the adjust lever is changed to “H: Envelope” position.*
1
• “Paper thickness lever was changed” or this image icon will be
displayed with LCD.*
2
PG close
(Displayed “L”)*
1
(“L” to “H”)*
2
• “L” will be displayed with 7 Segment 7 Segment LED for about 3
seconds just after the adjust lever is changed to “L: Cut sheet” position.
• “Paper thickness lever was changed” or this ima
ge icon will be
displayed with LCD.*
2
• Clear the PG error and print job suspended by PG error when the adjust
lever is changed to “L: Cut sheet position” in the PG error status.

Epson Stylus CX4900 Specifications

General

Brand	Epson
Model	Stylus CX4900
Category	Printer
Language	English