ESAB 100i - Page 207

Manual 0560956430 207 TORCH DATA 100i-400i
Stainless Steel
Flow Rates (SLPM / SCFH)
400A Bevel Cut
H17 N₂
Preow
- / - 207 / 439
H17 Plasma / N₂ Shield
Culow
47 / 100 173 / 367
Shield Cup
Shield Cap
Shield Gas
Distributor
Tip
Gas
Distributor
Electrode
Cartridge Assembly
This Art Is For Reference Only
Art# A-10444
Shield Cup Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
0559211401 0559210154 0559210083 0559210132 0559210065 0559210112 0559211400
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H17) Shield (N₂)
inch (in) (psi) Ball (psi) Ball (psi) (in) (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
1/2 0.080 30 120 100 NA 100 0.180 - 0.600 0.4 0.375 0.000 0.2
Not Recommended
without Elevaon Height
105 0.4 0.205
5/8 0.080 30 120 100 NA 100 0.200 - 0.600 0.6 0.375 0.300 0.2 90 0.6 0.200
3/4 0.080 30 120 100 NA 100 0.200 - 0.600 1.0 0.375 0.300 0.2 70 0.7 0.210
1 0.080 30 120 100 NA 100 0.200 - 0.600 1.5 0.375 0.300 0.2 50 1.2 0.212
1 1/4 0.080 30 120 100 NA 100 0.300 - 0.600 2.0 0.375 0.400 0.2 38 1.4 0.235
1 1/2 0.080 30 120 100 NA 100 0.300 - 0.600 2.8 0.375 0.500 0.2 30 2.0 0.245
1.750 0.080 30 120 100 NA 100 0.300 - 0.600 5.0 0.375 0.750 0.2 21 3.0 0.255
2.000 0.080 30 120 100 NA 100 0.300 - 0.600 8.0 0.375 0.750 0.2 17 5.5 0.280
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H17) Shield (N₂)
(mm) (mm) (Bar) Ball (Bar) Ball (Bar) (mm) (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
12 2.0 2.1 120 6.9 NA 6.9 4.5 - 15.2 0.4 9.5 0.0 0.2
Not Recommended without
Elevaon Height
2750 0.4 5.2
15 2.0 2.1 120 6.9 NA 6.9 4.9 - 15.2 0.5 9.5 5.5 0.2 2390 0.5 5.1
20 2.0 2.1 120 6.9 NA 6.9 5.1 - 15.2 1.1 9.5 7.6 0.2 1700 0.8 5.3
25 2.0 2.1 120 6.9 NA 6.9 5.1 - 15.2 1.5 9.5 7.6 0.2 1300 1.2 5.4
30 2.0 2.1 120 6.9 NA 6.9 6.9 - 15.2 1.9 9.5 9.5 0.2 1050 1.3 5.8
35 2.0 2.1 120 6.9 NA 6.9 7.6 - 15.2 2.4 9.5 11.5 0.2 860 1.7 6.1
40 2.0 2.1 120 6.9 NA 6.9 7.6 - 15.2 3.5 9.5 14.6 0.2 690 2.3 6.3
45 2.0 2.1 120 6.9 NA 6.9 7.6 - 15.2 5.3 9.5 19.1 0.2 520 3.2 6.5
50 2.0 2.1 120 6.9 NA 6.9 7.6 - 15.2 7.6 9.5 19.1 0.2 440 5.2 7.0
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.