Index (continued)
INDEX-5
OPT? remote command, 6-26
Options and Accessories, 9-3
Options and Accessories (Chapter 8), 9-3
Oscilloscope Calibration
Adjusting Output Signal, 8-14, 8-66
Amplitude, 8-16, 8-18, 8-69, 8-71
Commands and Queries, 8-34, 8-83
Edge Function, 8-19, 8-72
Frequency Response, 8-21, 8-24, 8-74, 8-78
Frequency Sweep, 8-24, 8-77
Horizontal Time Base, 8-26, 8-80
Introduction, 8-5, 8-59
Leveled Sine Wave Function, 8-21, 8-74
Marker Function, 8-26, 8-80
MORE OPTIONS menu, 8-23, 8-75
Oscilloscope Connection, 8-13, 8-65
Pulse Response, 8-19, 8-20, 8-21, 8-72, 8-73
Resetting Parameters, 8-15, 8-68
Starting, 8-13, 8-66
Testing the Trigger, 8-28, 8-82
Time Marker, 8-26, 8-80
TIme Marker, 8-27, 8-81
Trigger Connection, 8-13, 8-65
V/DIV menu, 8-17, 8-70
Volt Function, 8-16, 8-69
Voltage Gain, 8-16, 8-18, 8-69, 8-71
Wave Generator, 8-28, 8-82
Oscilloscope Calibration Specifications, 8-5, 8-60
Oscilloscope Commands, 6-6
Oscilloscope Connection
Channel and External Trigger, 8-13, 8-65
Oscilloscope Connections, 8-13, 8-65
OUT remote command, 6-27
OUT? remote command, 6-28
OUT_ERR? remote command, 6-29
Output Commands, 6-5
Output Display, 3-4
Output Editing, 4-49
Output Limits, Setting of, 4-50
Output Queue, 5-42
Output Setting
AC Current, 4-22
AC Power, 4-25
AC Voltage, 4-19
Capacitance, 4-33
DC Current, 4-21
dc offset, 4-46
DC Power, 4-24
DC Voltage, 4-18
Dual AC Voltage, 4-30
Dual DC Voltage, 4-28
Phase Adjusting, 4-43
Power Factor, 4-45
Resistance, 4-32
Temperature Simulation, 4-35
Temperature Simulation (RTD), 4-37
Output Signal
Adjusting for Oscilloscope Calibration, 8-14, 8-66
Overlapped Commands, 5-29
—P—
Parameter Syntax Rules, 5-31
Peak-to-Peak Versus Rms Waveforms, 4-16
Performances Tests, 7-7
PF. See Power Factor
Phase Accuracy, 7-22
Phase Angle, Entering a, 4-44
PHASE remote command, 6-29
PHASE? remote command, 6-29
Placement of Calibrator, 2-7
Power
AC Output Setting, 4-25
DC Output Setting, 4-24
Power Cords, 2-6
Power Factor, Entering of, 4-45
POWER? remote command, 6-30
Preparing for Operation (Chapter 2), 2-3
PREV MENU key, 3-5
Program Examples
Remote, 5-43
Taking a Thermocouple Measurement, 5-46
Using *OPC?, *OPC, and *WAI, 5-45
Verifying a Meter on IEEE-488 Bus, 5-45
Verifying a Meter on RS-232 Bus, 5-45
Writing an Error Handler, 5-44
Writing an SRQ handler, 5-44
Programming
The ESR and ESE, 5-39
the STB and SRE, 5-38
Programming the Calibrator, 5-43
PUD remote command, 6-30
PUD? remote command, 6-31
Pulse Response Calibration, 8-19, 8-20, 8-21, 8-72, 8-
73
—Q—
Query Commands, 5-26
Queue
Output, 5-42
—R—
Rack Mount Kit, 9-4
Rack Mounting, 2-7
RANGE? remote command, 6-31
RANGELCK remote command, 6-31
RANGELCK? remote command, 6-32
Rear Panel Features, 3-3
Recommended Cable and Connector Types, 4-9
To Next Page
Loading...
