Fluke 5500A - Page 408

5500A
Operator Manual
INDEX-6
REFOUT? remote command, 6-32
Registers
Event Status (ESR), 5-38
Event Status Enable (ESE), 5-38
Instrument Status (ISR), 5-40
Instrument Status Change (ISCR), 5-40
Instrument Status Change Enable (ISCE), 5-40
Remote Commands (Chapter 6), 6-3
Remote Control
Using Host Port, 5-10, 5-15
Using IEEE Port, 5-4
Remote Operation (Chapter 5), 5-4
Remote Operation (IEEE-488), 1-5
Remote Program Examples, 5-43
REMOTE remote command, 6-32
Remote State, 5-21
Remote with Lockout State, 5-21
Replacing the Line Fuse, 7-3
RESET key, 3-6
Resetting the Calibrator, 4-7
Resistance Accuracy, 7-10
Resistance DC Offset Measurement, 7-11
Resistance Output Setting, 4-32
Response Data Types
Binary Block Data, 5-34
Floating, 5-34
Indefinite ASCII, 5-34
Integer, 5-34
String, 5-34
Table of, 5-34
Response Message Syntax, 5-34
Rms Versus Peak-to-Peak Waveforms, 4-16
RS-232
Controlling an Instrument, 5-46
Host Port Setup Procedure, 5-10
Using Host Port, 5-10, 5-15
UUT Port Setup Procedure, 5-15
RS-232 Host Port Commands, 6-6
RS-232 Host Port Operation using a Terminal, 5-12
RS-232 Host Port Operation using Visual Basic, 5-14
RS-232 Host Port Setup Procedure, 5-10
RS-232 Host Port, Testing the, 5-12
RS-232 Interface Overview, 5-22
RS-232 Modem Cables, 9-4
RS-232 Null-Modem Cables, 9-4
RS-232 Remote Control Connections, 5-6
RS-232 UUT Port Commands, 6-7
RS-232 UUT Port Operation using Visual Basic, 5-18
RS-232 UUT Port Operation via a Terminal, 5-17
RS-232 UUT Port Setup Procedure, 5-15
RS-232 UUT Port testing via IEEE-488 Port, 5-19
RS-232 UUT Port testing via RS-232 Host Port, 5-17
RST remote command, 6-33
RTD, Setting Temperature Simulation, 4-37
RTD_TYPE remote command, 6-33
RTD_TYPE? remote command, 6-33
RTD_TYPE_D remote command, 6-34
RTD_TYPE_D? remote command, 6-34
—S—
Sample Applications, 4-52
SCOPE key, 3-5
Selecting an External Amplifier, 4-5
Sequential Commands, 5-29
Serial Poll
Status Byte, 5-35
Service
Information, 2-6
Service Request
SRQ Line, 5-37
SERVICE REQUEST
Enable Register (SRE), 5-37
Setting a Dual AC Voltage Output, 4-30
Setting a Dual DC Voltage Output, 4-28
Setting AC Current Output, 4-22
Setting AC Power Output, 4-25
Setting AC Voltage Output, 4-19
Setting Capacitance Output, 4-33
Setting DC Current Output, 4-21
Setting DC Power Output, 4-24
Setting DC Voltage Output, 4-18
Setting Harmonics, 4-42
Setting Output Limits, 4-50
Setting Resistance Output, 4-32
Setting Temperature Simulation (RTD), 4-37
Setting Temperature Simulation (Thermocouple), 4-35
Setting the Output, 4-17
Setting up the RS-232 Host Port for Remote Control,
5-10
Setting up the RS-232 UUT Port for Remote Control,
5-15
Setting Voltage and Current Limits, 4-51
Setup and Utility Commands, 6-6
SETUP key, 3-6
Setup menu, 4-4
Setup Menus
Format EEPROM menu, 4-6
IEEE-488 Port, 5-7
Instrument Setup, 4-5
RS-232 Host Port, 5-10
Utility Functions Menu, 4-6
SETUP Softkey Menu Tree, 3-12
SHIFT key, 3-8
Shortcuts for Setting the Voltage Amplitude, 8-17
Signal
Adjusting during Oscilloscope Calibration, 8-14, 8-
66
Sinewave, 4-41
Softkey Menu Trees, 3-3