EasyManua.ls Logo

GEFRAN-SIEI ARTDrive Vector V2 Series - Page 353

GEFRAN-SIEI ARTDrive Vector V2 Series
387 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
ARTDrive V2 series - Instruction Manual Chapter 8 Appendix • 353
Alarm name Description Drive Hold off Restart Restart Code in Bit posi-
(Cause of fault) activity time the Alarm tion in
After alarm list Al.list
ISBus faultISBus fault
ISBus faultISBus fault
ISBus fault Fault of optional ISBus Programmable No Yes Program. 36 16
LAN communication
Comm carComm car
Comm carComm car
Comm car
d faultd fault
d faultd fault
d fault Fault of optional LAN Programmable No Yes Program. 37 17
communication board
Appl carAppl car
Appl carAppl car
Appl car
d faultd fault
d faultd fault
d fault Fault of optional application Disable drive No No No 38 18
coprocessor board
Drv overloadDrv overload
Drv overloadDrv overload
Drv overload Drive overload accumulator Programmable No No No 39 19
exceeded trip threshold
Mot overloadMot overload
Mot overloadMot overload
Mot overload Motor overload accumulator Programmable No No No 40 20
exceeded trip threshold
BU overloadBU overload
BU overloadBU overload
BU overload Braking resistor overload Programmable No No No 41 21
accumulator exceeded trip
threshold
Data lostData lost
Data lostData lost
Data lost Data corrupted in non-volatile Disable drive No No No 42 22
memory
Fwd RFwd R
Fwd RFwd R
Fwd R
ev Ctrlev Ctrl
ev Ctrlev Ctrl
ev Ctrl Forward and Reverse commands Programmable No No No 43 23
were detected active at the
same time
Max timeMax time
Max timeMax time
Max time Software task time overrun Disable drive No No No 44 24
was detected
SequencerSequencer
SequencerSequencer
Sequencer Command sequencer was Disable drive No No No 45 25
tripped by an alarm event
PLS timeoutPLS timeout
PLS timeoutPLS timeout
PLS timeout The duration of a voltage dip Disable drive No No No 46 26
caused Power Loss Stop function
restart logic to timeout
OverspeedOverspeed
OverspeedOverspeed
Overspeed Maximum speed threshold was Programmable Programmable No No 47 27
exceeded while drive in RUN state
UV rUV r
UV rUV r
UV r
epetitiveepetitive
epetitiveepetitive
epetitive More than a programmable Disable drive. No No No 48 28
number of UV fault were If n. of faults is
detected in 5 minutes set to max, the
Alarm is disabled.
IOC rIOC r
IOC rIOC r
IOC r
epetitiveepetitive
epetitiveepetitive
epetitive More than 2 OC faults were Disable drive No No No 49 29
detected in 30 sec.
IGBTdesat rIGBTdesat r
IGBTdesat rIGBTdesat r
IGBTdesat r
epetepet
epetepet
epet More than 2 IGBT desat faults Disable drive No No No 50 30
were detected in 30 sec.
WW
WW
W
atchDog useratchDog user
atchDog useratchDog user
atchDog user The drive failed to retrigger the Disable drive No No No 51 31
communication watchdog within
the specified time
Hw failHw fail
Hw failHw fail
Hw fail Communication failure between Disable drive No No No 52 32
Drive Regulation board and one
of its options or I/O expansions.

Table of Contents

Related product manuals