ARTDrive V2 series - Instruction Manual Chapter 4 Wiring Procedure • 61
4.7.1 AC Input Chokes
Table 4.7.1.1: 3-Phase AC Input Chokes
Mains
inductance
Rated
current
Saturation
current
Freq.
[mH] [A] [A] [Hz]
abcD1E1
1007 6.1 2.5 5 50/60
LR3y-1007
S7AAD
1015 3.69 3.7 7.4 50/60 LR3y-1015
S7AAE
1022 2.71 5.5 11 50/60 LR3y-1022
S7AAF
1030 2.3 6.7 14 50/60 LR3y-1030
S7AB3
2040 1.63 8.7 18 50/60 LR3y-2040
S7AAG 2 (4.4)
2055 1.29 11.8 24.5 50/60 LR3y-2055 S7AB5
2.2 (4.4) 120 (4.7) 125 (4.9) 75 (2.6) 100 (3.9) 55 (2.2)
2075 0.89 17.4 36.5 50/60 LR3y-2075 S7AB6
4.9 (10.8) 150 (5.9) 155 (6.1) 79 (3.1) 90 (3.5) 54 (2.1)
3110 0.68 22.4 46.5 50/60 LR3y-3110 S7AB7
5 (11) 150 (5.9) 155 (6.1) 79 (3.1) 90 (3.5) 54 (2.1)
3150 0.51 30 61 50/60 LR3y-3150 S7AB8
6.2 (13.7) 150 (5.9) 169 (6.7) 85 (3.3) 90 (3.5) 56 (2.2)
4220
0.35 41 83 50/60
LR3-022 S7FF4 7.8 (17.2) 180 (7.1) 182 (7.2) 130 (5.1) 150 (5.9) 74 (2.9)
4300
0.24 58 120 50/60
LR3-030 S7FF3 9.5 (20.9) 180 (7.1) 165 (6.5) 160 (6.3) 150 (5.9) 74 (2.9)
4370
0.18 71 145 50/60
LR3-037 S7FF2 9.5 (20.9) 180 (7.1) 160 (6.3) 180 (7.1) 150 (5.9) 80 (3.1)
5450
0.13 102 212 50/60
5550
0.13 102 212 50/60
6750
0.148 173 350 50/60
7900
0.148 173 350 50/60
71100
0.085 297 600 50/60
71320
0.085 297 600 50/60
81600
0.085 297 600 50/60
2002
4.5 4.2 8.4 50/60
LR3y-5-002 S7AD0 2 (4.4) 120 (4.7) 125 (4.9) 75 (2.6) 100 (3.9) 42 (1.6)
2003
3.8 5.2 10.4 50/60
LR3y-5-003 S7AD2 2 (4.4) 120 (4.7) 125 (4.9) 75 (2.6) 100 (3.9) 42 (1.6)
2005
2.3 8.1 16.2 50/60
LR3y-5-005 S7AD3 2.7 (6) 120 (4.7) 125 (4.9) 85 (3.3) 100 (3.9) 52 (2)
3007
1.5 12.9 25.8 50/60
LR3y-5-007 S7AC7 5 (11) 150 (5.9) 152 (6) 80 (3.1) 90 (3.5) 55 (2.2)
3010
1.2 16.5 33.0 50/60
LR3y-5-010 S7AC8 5 (11) 150 (5.9) 152 (6) 80 (3.1) 90 (3.5) 55 (2.2)
3015
0.9 21.8 43.6 50/60
LR3y-5-015 S7AC9 5.5 (12.1) 150 (5.9) 164 (6.4) 96 (3.8) 90 (3.5) 60 (2.4)
3020
0.7 28.5 57 50/60
LR3y-5-020 S7AD1 6.2 (13.7) 150 (5.9) 164 (6.4) 106 (4.2) 90 (3.5) 70 (2.8)
avy0703
120 (4.7)
AVy…-5 (575V)
AVy…-4 (230V…480V)
Drive type
LR3-055
LR3-090
LR3-160
Three-phases main chokes
94 (3.7)
S7D40
85 (3.3)
Model
Weight
kg (lbs)
12.5 (27.6)
55 (121.3)
code
S7FF1
S7D19
168 (6.6) 180 (7.1)
44 (97.0)
Dimensions : mm (inch)
120 (4.72) 125 (4.92) 65 (2.56) 100 (3.94) 45 (1.77)
1.8 (3.9)
1.9 (4.2)
180 (7.1) 150 (5.9)
300 (11.8) 265 (10.4) 210 (8.3) 250 (9.8)
300 (11.8) 270 (10.6) 260 (10.2) 250 (9.8)
For sizes up to 20Hp, an input choke is strongly reccomended in order to:
- prolong the life time of the DC link capacitors and the reliability of the input
rectifier.
- reduce the AC line harmonic distortion
- reduce problems due to low impedence AC line (≤ 1%).
NOTE! The current rating of these chokes (reactors) is based on nominal current of
standard motors, listed in table 2.3.4.1 in section 2.3.4, “AC Output”.
NOTE! The 4025 … 8200 sizes of AVy-5 series (575Vac), integrate as standard the
input choke on intermediate circuit (DC-Link). With this configuration the three
phase input choke it is NOT required.
4.7.2 Output Chokes
The AVy Drive can be used with general purpose standard motors or with motors
specially designed for Drive use. The latter usually have a higher isolation rating
to better withstand PWM voltage.
Motors designed for use with Adjustable Frequency Drives do not require any
specific filtering of the voltage waveform from the Drive.
For general purpose motors, especially with long cable runs (typically over 100
m [328 feet]), an output choke is recommended to maintain the voltage waveform
within the specified limits.
The choke must be installed as close as possible to the drive side end of the
cable run.
Suggested choke ratings and part numbers are listed in table 4.7.2.1.
The rated current of the filters should be approx. 20% above the rated current of
To Next Page
Loading...