Helmer iB111 (Version A) - Section IV: Horizon Series - Laboratory, Pharmacy, and International Blood Bank Models; 23 Product Configuration

138 pages

Save Page as PDF

To Next Page

To Previous Page

360077-1/O 105

Horizon Series™ - Blood Bank Models

VIEW CONFIGURATION screen

Clock Mode display

Date Format display

Door Ajar Timeout display

Pwr Failure Timeout display

High Alarm Setpoint display

Low Alarm Setpoint display

Alarm Volume display

Alarm Pulse display

Chart Paper Days Left or Chart Paper Timer display

Main Page

Default Chapter3
- Table of Contents3
Section I: General Information9
1 About this Manual9
- Copyright and Trademark9
- Intended Audience9
- Model References9
2 Safety9
- Safety Definitions9
- Product Labels10
- Avoiding Injury10
Configuration11
- Model and Input Power11
- Control System11
- Temperature Probes13
- Internal Outlet14
- Chart Recorder14
  - Chart Recorder Access15
  - Install Chart Paper15
4 Alarm Reference16
5 Compliance16
- Regulatory Compliance16
- WEEE Compliance16
6 Warranty17
- Rel.I™ Product Warranty USA and Canada17
- Outside of USA and Canada18
Section II: I.series ® - All Models19
Product Configuration19
- Install Battery for Backup Power19
- External Monitoring Devices20
  - Connect to Remote Alarm Interface20
- Move Drawers, Shelves, and Baskets21
- Drawer Labels22
- Move Slides and Brackets22
- Optional Adapter Kits for Medication Dispensing Locks22
8 Temperature Monitor Settings23
- Home Screen23
  - Home Screen Functions23
- Main Screen24
- Temperature Graph25
  - Enable or Disable the Temperature Graph25
- Change Configuration Password26
- Calibrate Chamber Temperature Probe26
- Factory Default Settings27
- Restore Factory Default Settings27
- Alarm Settings28
- Test Alarms31
- Additional System Settings34
- Event Log36
  - Event Details37
- Upgrade System Firmware37
- Reset the I.center Monitoring System37
- View Manufacturer and Product Information38
9 Temperature Controller Setpoints38
- Level 1 Parameters and Values39
- Level 2 Parameters and Values40
- Level 3 Parameters and Values40
- Level 4 Parameters and Values41
- Change the Refrigerator Setpoint41
- Change the Hysteresis Value42
10 Maintenance42
- Recharge Refrigerant42
- Test Monitoring System Backup Batteries43
- Replace Monitoring System Backup Batteries43
- Replace the Fluorescent Lamps43
- Clean the Refrigerator43
- Unit Cooler Cover Removal and Installation45
  - Remove the Unit Cooler Cover45
  - Install the Unit Cooler Cover46
- Supplies46
11 Troubleshooting47
- General Operation Problems47
- Chamber Temperature Problems48
- Alarm Activation Problems49
- Testing Problems52
- Condensation Problems52
12 Parts53
- Front53
  - Display54
- Top55
- Rear56
  - Electrical Box57
- Interior58
13 Schematics63
- Ib and Ihb Models; 11, 20, 25, 45, 56 Cubic Feet63
- Ilr, Ipr Models; 11 Cubic Feet64
- Ilr and Ipr Models; 20, 25, 45, and 56 Cubic Feet65
14 I.center Screen Reference66
Section III: Horizon Series™ - Blood Bank Models68
Product Configuration68
- Install Battery for Backup Power68
- External Monitoring Devices69
  - Connect to Remote Alarm Interface69
- Move Drawers, Shelves, and Baskets70
- Move Slides and Brackets71
- Optional Adapter Kits for Medication Dispensing Locks71
16 Temperature Monitor Settings71
- Home Screen71
  - Home Screen Functions72
- Main Screen72
- Change Configuration Password73
- Calibrate Chamber Temperature Probe73
- Factory Default Settings74
- Restore Factory Default Settings74
- Alarm Settings75
- Test Alarms78
- Additional System Settings80
- Upgrade System Firmware81
- Reset the Horizon Series Monitoring System81
- View Manufacturer and Product Information81
17 Temperature Controller Setpoints82
- Level 1 Parameters and Values83
- Level 2 Parameters and Values84
- Level 3 Parameters and Values84
- Level 4 Parameters and Values85
- Change the Refrigerator Setpoint85
- Change the Hysteresis Value86
18 Maintenance86
- Recharge Refrigerant86
- Test Monitoring System Backup Batteries87
- Replace the Fluorescent Lamps87
- Clean the Refrigerator87
- Unit Cooler Cover Removal and Installation88
  - Remove the Unit Cooler Cover89
  - Install the Unit Cooler Cover89
- Supplies89
19 Troubleshooting90
- General Operation Problems90
- Chamber Temperature Problems91
- Alarm Activation Problems92
- Condensation Problems94
20 Parts95
- Front95
  - Horizon Display96
- Top97
- Rear98
  - Electrical Box99
- Interior100
21 Schematics104
- HB Models; 11, 20, 25, 45, 56 Cubic Feet104
22 Horizon Series Screen Reference105
Section IV: Horizon Series™ - Laboratory, Pharmacy, and International Blood107
- Bank Models107
Product Configuration107
- Install Battery for Backup Power107
- External Monitoring Devices108
  - Connect to Remote Alarm Interface108
- Move Drawers, Shelves, and Baskets109
- Move Slides and Brackets110
- Optional Adapter Kits for Medication Dispensing Locks110
24 Settings110
- Monitor and Controller Interface111
- Refrigerator Setpoint112
- Temperature Alarm Setpoints112
  - High Temperature Alarm113
  - Low Temperature Alarm113
- Temperature Calibration Setpoints113
- Test Alarms115
25 Maintenance117
- Recharge Refrigerant117
- Test Monitoring System Backup Batteries118
- Replace the Fluorescent Lamps118
- Clean the Refrigerator118
- Unit Cooler Cover Removal and Installation119
  - Remove the Unit Cooler Cover120
  - Install the Unit Cooler Cover120
- Supplies120
26 Troubleshooting121
- General Operation Problems121
- Chamber Temperature Problems122
- Alarm Activation Problems123
- Condensation Problems125
27 Parts126
- Front126
  - Laboratory Display127
- Top127
- Rear128
  - Electrical Box129
- Interior130
28 Schematics134
- HLR and HPR Models; 11 Cubic Feet134
- HLR and HPR Models; 20, 25, 45, 56 Cubic Feet135
- HHB Models; 11, 20, 25, 45, 56 Cubic Feet136

Helmer iB111 (Version A) - Section IV: Horizon Series - Laboratory, Pharmacy, and International Blood Bank Models; 23 Product Configuration

Table of Contents

Related product manuals