Helmer iB111 (Version A)

To Previous Page

HELMER SCIENTIFIC

14400 Bergen Boulevard

Noblesville, IN 46060 USA

PH +1.317.773.9073

FAX +1.317.773.9082

www.helmerinc.com

Main Page

Default Chapter3
- Table of Contents3
Section I: General Information9
1 About this Manual9
- Copyright and Trademark9
- Intended Audience9
- Model References9
2 Safety9
- Safety Definitions9
- Product Labels10
- Avoiding Injury10
Configuration11
- Model and Input Power11
- Control System11
- Temperature Probes13
- Internal Outlet14
- Chart Recorder14
  - Chart Recorder Access15
  - Install Chart Paper15
4 Alarm Reference16
5 Compliance16
- Regulatory Compliance16
- WEEE Compliance16
6 Warranty17
- Rel.I™ Product Warranty USA and Canada17
- Outside of USA and Canada18
Section II: I.series ® - All Models19
Product Configuration19
- Install Battery for Backup Power19
- External Monitoring Devices20
  - Connect to Remote Alarm Interface20
- Move Drawers, Shelves, and Baskets21
- Drawer Labels22
- Move Slides and Brackets22
- Optional Adapter Kits for Medication Dispensing Locks22
8 Temperature Monitor Settings23
- Home Screen23
  - Home Screen Functions23
- Main Screen24
- Temperature Graph25
  - Enable or Disable the Temperature Graph25
- Change Configuration Password26
- Calibrate Chamber Temperature Probe26
- Factory Default Settings27
- Restore Factory Default Settings27
- Alarm Settings28
- Test Alarms31
- Additional System Settings34
- Event Log36
  - Event Details37
- Upgrade System Firmware37
- Reset the I.center Monitoring System37
- View Manufacturer and Product Information38
9 Temperature Controller Setpoints38
- Level 1 Parameters and Values39
- Level 2 Parameters and Values40
- Level 3 Parameters and Values40
- Level 4 Parameters and Values41
- Change the Refrigerator Setpoint41
- Change the Hysteresis Value42
10 Maintenance42
- Recharge Refrigerant42
- Test Monitoring System Backup Batteries43
- Replace Monitoring System Backup Batteries43
- Replace the Fluorescent Lamps43
- Clean the Refrigerator43
- Unit Cooler Cover Removal and Installation45
  - Remove the Unit Cooler Cover45
  - Install the Unit Cooler Cover46
- Supplies46
11 Troubleshooting47
- General Operation Problems47
- Chamber Temperature Problems48
- Alarm Activation Problems49
- Testing Problems52
- Condensation Problems52
12 Parts53
- Front53
  - Display54
- Top55
- Rear56
  - Electrical Box57
- Interior58
13 Schematics63
- Ib and Ihb Models; 11, 20, 25, 45, 56 Cubic Feet63
- Ilr, Ipr Models; 11 Cubic Feet64
- Ilr and Ipr Models; 20, 25, 45, and 56 Cubic Feet65
14 I.center Screen Reference66
Section III: Horizon Series™ - Blood Bank Models68
Product Configuration68
- Install Battery for Backup Power68
- External Monitoring Devices69
  - Connect to Remote Alarm Interface69
- Move Drawers, Shelves, and Baskets70
- Move Slides and Brackets71
- Optional Adapter Kits for Medication Dispensing Locks71
16 Temperature Monitor Settings71
- Home Screen71
  - Home Screen Functions72
- Main Screen72
- Change Configuration Password73
- Calibrate Chamber Temperature Probe73
- Factory Default Settings74
- Restore Factory Default Settings74
- Alarm Settings75
- Test Alarms78
- Additional System Settings80
- Upgrade System Firmware81
- Reset the Horizon Series Monitoring System81
- View Manufacturer and Product Information81
17 Temperature Controller Setpoints82
- Level 1 Parameters and Values83
- Level 2 Parameters and Values84
- Level 3 Parameters and Values84
- Level 4 Parameters and Values85
- Change the Refrigerator Setpoint85
- Change the Hysteresis Value86
18 Maintenance86
- Recharge Refrigerant86
- Test Monitoring System Backup Batteries87
- Replace the Fluorescent Lamps87
- Clean the Refrigerator87
- Unit Cooler Cover Removal and Installation88
  - Remove the Unit Cooler Cover89
  - Install the Unit Cooler Cover89
- Supplies89
19 Troubleshooting90
- General Operation Problems90
- Chamber Temperature Problems91
- Alarm Activation Problems92
- Condensation Problems94
20 Parts95
- Front95
  - Horizon Display96
- Top97
- Rear98
  - Electrical Box99
- Interior100
21 Schematics104
- HB Models; 11, 20, 25, 45, 56 Cubic Feet104
22 Horizon Series Screen Reference105
Section IV: Horizon Series™ - Laboratory, Pharmacy, and International Blood107
- Bank Models107
Product Configuration107
- Install Battery for Backup Power107
- External Monitoring Devices108
  - Connect to Remote Alarm Interface108
- Move Drawers, Shelves, and Baskets109
- Move Slides and Brackets110
- Optional Adapter Kits for Medication Dispensing Locks110
24 Settings110
- Monitor and Controller Interface111
- Refrigerator Setpoint112
- Temperature Alarm Setpoints112
  - High Temperature Alarm113
  - Low Temperature Alarm113
- Temperature Calibration Setpoints113
- Test Alarms115
25 Maintenance117
- Recharge Refrigerant117
- Test Monitoring System Backup Batteries118
- Replace the Fluorescent Lamps118
- Clean the Refrigerator118
- Unit Cooler Cover Removal and Installation119
  - Remove the Unit Cooler Cover120
  - Install the Unit Cooler Cover120
- Supplies120
26 Troubleshooting121
- General Operation Problems121
- Chamber Temperature Problems122
- Alarm Activation Problems123
- Condensation Problems125
27 Parts126
- Front126
  - Laboratory Display127
- Top127
- Rear128
  - Electrical Box129
- Interior130
28 Schematics134
- HLR and HPR Models; 11 Cubic Feet134
- HLR and HPR Models; 20, 25, 45, 56 Cubic Feet135
- HHB Models; 11, 20, 25, 45, 56 Cubic Feet136

Helmer iB111 (Version A) - Page 138

Table of Contents

Related product manuals