IBM SAN192C-6 User Manual

Mod MAC-Address(es) Serial-Num
--- -------------------------------------- ----------
1 84-78-ac-1b-3d-58 to 84-78-ac-1b-3d-8b JAF1718AAAD
2 f4-cf-e2-7c-cd-30 to f4-cf-e2-7c-cd-33 JAE1847038X
3 04-6c-9d-32-36-aa to 04-6c-9d-32-37-1b JAE19330ASN
4 00-76-86-bf-58-23 to 00-76-86-bf-58-57 JAE203901ZG
5 00-2f-5c-fc-54-0a to 00-2f-5c-fc-54-1d JAE22440CB1
6 00-00-00-00-00-00 to 00-00-00-00-00-00 NA
7 00-da-55-a2-25-00 to 00-da-55-a2-25-0f JAE195004XM
8 74-86-0b-33-c6-70 to 74-86-0b-33-c6-a4 JAE213101Q3
10 3c-0e-23-c5-53-d0 to 3c-0e-23-c5-53-d3 JAE180605X3
Mod Online Diag Status
--- ------------------
1 Pass
2 Pass
3 Pass
4 Pass
5 Pass
7 Pass
8 Pass
10 Pass
Xbar Ports Module-Type Model Status
--- ----- ---------------- -------------- ----------
1 0 Fabric Module 1 DS-X9710-FAB1 ok
2 0 Fabric Module 1 DS-X9710-FAB1 ok
3 0 Fabric Module 1 DS-X9710-FAB1 ok
4 0 Fabric Module 1 DS-X9710-FAB1 ok
5 0 Fabric Module 1 DS-X9710-FAB1 ok
6 0 Fabric Module 1 DS-X9710-FAB1 ok
Xbar Sw Hw
--- ------ ------
1 NA 1.0
2 NA 1.0
3 NA 1.0
4 NA 1.0
5 NA 1.0
6 NA 1.0
Xbar MAC-Address(es) Serial-Num
---- ---------------- ----------
1 NA JAE222305VS
2 NA JAE2217096X
3 NA JAE222305V5
4 NA JAE2217096L
5 NA JAE2217096J
6 NA JAE222305V8
12. (Optional) If the standby Supervisor-1 Module is not in the powered-dn state, then put the
standbySupervisor-1 Module to out of service, using the out-of-service module slot command
Where a slot indicates the chassis slot number in which the standby supervisor module resides.
switch(config)# out-of-service module 6
13. Physically replace the standby Supervisor-1 Module (slot 6) with the second Supervisor-4 Module. To
replace the supervisor module, follow the steps explained in “Installing Supervisor Modules” on page
79 and “Removing Supervisor Modules” on page 80.
The following message is displayed:
2019 Jun 25 15:21:13 switch %PLATFORM-2-SINGLE_EJECTOR_STAT_CHANGED:
Ejector's status in slot 6 has changed, Ejector is OPEN
2019 Jun 25 15:21:15 switch %PLATFORM-2-MOD_REMOVE:
Module 6 removed (Serial number JAE17440HVB)
After inserting the new standby Supervisor-4 Module, the following message is displayed:
2019 Jun 25 15:21:27 switch %PLATFORM-2-MODULE_EJECTOR_POLICY_ENABLED:
All Ejectors closed for module 6. Ejector based shutdown enabled
90IBM Storage Networking SAN192C-6, SAN384C-6 and SAN768C-6: SAN192C-6, SAN384C-6 and
SAN768C-6 Installation, Service, and User Guide

IBM SAN192C-6 Specifications

General

Brand	IBM
Model	SAN192C-6
Category	Storage
Language	English